Table of Contents
Advertisement
Quick Links
FITBOARD 4D VIBRATION PLATFORM
EXERCISE MACHINE
SF-VP822058
USER MANUAL
IMPORTANT! Please retain owner's manual for maintenance and adjustment instructions. Your
satisfaction is very important to us, PLEASE DO NOT RETURN UNTIL YOU HAVE CONTACTED
US:
support@sunnyhealthfitness.com
or 1-877-90SUNNY (877-907-8669).
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Sunny FITBOARD SF-VP822058
Summary of Contents for Sunny FITBOARD SF-VP822058
- Page 1 FITBOARD 4D VIBRATION PLATFORM EXERCISE MACHINE SF-VP822058 USER MANUAL IMPORTANT! Please retain owner’s manual for maintenance and adjustment instructions. Your satisfaction is very important to us, PLEASE DO NOT RETURN UNTIL YOU HAVE CONTACTED support@sunnyhealthfitness.com or 1-877-90SUNNY (877-907-8669).
-
Page 2: Important Safety Information
IMPORTANT SAFETY INFORMATION We thank you for choosing our product. To ensure your safety and health, please use this equipment correctly. It is important to read this entire manual before assembling and using the equipment. Safe and effective use can only be achieved if the equipment is assembled, maintained, and used properly. -
Page 3: Exploded Diagram
EXPLODED DIAGRAM 1... - Page 4 EXPLODED DIAGRAM 2...
-
Page 5: Parts List
PARTS LIST Description Spec. Qty. Description Spec. Qty. Hexagon 3 in 1 Stepping Rubber 631.7*354.3*3.7 M5*14 Screw Light Cover 308.5*69.5*26.5 Hexagon Screw M5*20 8 Type Connecting Light Strip 330*10 75*40*1.5 Gasket 2 8 Type Connecting Upper Cover 780*439.7*94 75*40*8 Rod 2 Deep Groove Ball Upper Control Panel 130*65*21... - Page 6 ASSEMBLY CONTENTS WHEN OPENING THE CARTON, THE FOLLOWING PARTS CAN BE FOUND: Manual Main Product Thank You Card Remote Control Power Cord Button Cell Battery...
-
Page 7: Important Electrical Information
IMPORTANT ELECTRICAL INFORMATION IMPORTANT NOTE: This machine requires a power source of 110 Volts in order to properly operate. For your safety, as well as the safety of others, please verify that the power source is correct before powering the machine. Any power supply source above or below this level could cause significant damage to the machine and/or user. -
Page 8: Battery Installation And Replacement
BATTERY INSTALLATION AND REPLACEMENT BATTERY INSTALLATION: 1. Remove the battery card slot from the Remote Control (No. 48). 2. Take out the 1 pc battery that is included inside the remote control plastic bag. 3. Install the battery into the battery card slot with the CR2025 side facing up. 4. -
Page 9: Operating The Control Unit
THE DISPLAY CONSOLE OPERATING THE CONTROL UNIT... -
Page 10: Operating The Remote Control
OPERATING THE REMOTE CONTROL Power key Start/Stop Decrease speed Increase speed Decrease time Increase time Mode key Program key Quick adjustment for speed, level 10 in manual mode Quick adjustment for speed, level 20 in manual mode Quick adjustment for speed, level 30 in manual mode To start the unit, please connect the Power Cord (No. -
Page 11: Troubleshooting
Start/Stop: If you press the start/stop key, the machine starts moving after a 3 second countdown. When press again, the machine stops moving. Power Key: Always switch off the machine with this power key after the end of the training session. You can also switch the machine off with the power key when it’s in motion. -
Page 12: Usage Instruction
USAGE INSTRUCTION 1. Sit on the Stepping Rubber (No. 1) with your back straight and put your hands on your knees. This exercise aims to relax the hips and buttocks. (Fig. 2) Fig. 2 2. Sit in front of the machine, keep your back straight and place your feet on the Stepping Rubber (No. - Page 13 4. Sit on a chair in front of the machine and place your feet on the Stepping Rubber (No. 1) for a relaxing vibration massage. This exercise is good for the lower and upper thighs. (Fig. 5) Fig. 5 5. Transport the machine: lift the opposite side of the Transportation Wheel (No. 45) until the Transportation Wheel (No.
- Page 14 Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Need help?
Do you have a question about the FITBOARD SF-VP822058 and is the answer not in the manual?
Questions and answers