Table of Contents
Advertisement
For neck and head protection from the thermal effects of an electric arc flash, the use of
a Salisbury PrismShield™ Plus Arc Flash Protective Hood with an identical ATPV class to
the Pro-Wear™ Plus PPE is recommended. Please contact Salisbury for further details or
questions. For enhanced eye protection safety glasses complying to ANSI/ISEA Z87.1
are recommended.
INSTRUCTIONS FOR PRISMSHIELD™ PLUS PRO HOOD
The PrismShield™ Plus PPE must be used in conjunction with personal protective
equipment of similar protective characteristics covering the rest of the user's body.
For limb and torso protection, it is recommended that either a Salisbury Pro-Wear™ Plus Arc
Flash Protection Coverall, or Salisbury Pro-Wear™ Plus Coat and Salisbury Pro-Wear™ Plus
Arc Flash Protective Bib Overall combination be used. Please contact Salisbury for further
details.
INSTRUCTIONS FOR PRISMSHIELD™ PLUS LIFT FRONT HOOD™
Inspection of the face shield:
1. Ensure that face shield and fabric shroud have the same ATPV/EBT ratings.
2. Inspect Lift Front Hood prior to each use to ensure that there are no gaps that would
expose the user to an arc flash.
3. Inspect the product before each use to ensure there are no cracks in the plastic
components, tears in the fabric shroud or any other visible damage.
4. Inspect the hinge mechanism and ensure that all plastic locking points are secure.
5. If any of the above do not pass inspection, replace the product or component before using.
Using the face shield:
1. To stow the face shield in the weight balancing position, lift the shield by squeezing
the tab and lifting into the up and stowed position. Visor will lock in stowed postion,
if it is loose, tighten the visor by rotating wheel on both sides of visor.
2. To lower the shield into the deployed position, grasp the tab and pull the shield
down until there is an audible click. Assure that the shield is in the final lowered
position before use.
Rotate the wheel to
tighten the visor
Opening &
Closing Tab
Hood in deployed position
8
Hood in stowed position
NOTE: NEVER LEAVE THE SHIELD IN THE STOWED POSTION WHEN INSIDE
THE APPROACH BOUNDERIES AS DEFINED BY NFPA 70E
Care instructions
Face shield:
Wash with mild detergent and water. Rinse. Dry with soft cloth or chamois. If required,
disassemble frame at joints and remove the window to clean the entire assembly. The
pivot mechanism must not be disassembled. These components may be cleaned by
washing with mild detergent under running water and air dried.
Fabric shroud:
Remove fabric shroud from hard hat/face shield assembly and follow care instructions
for arc flash garments outlined in this booklet.
NOTE: THE PPE OUTLINED WITH THE LOWEST ATPV CLASS PROTECTION IS
THE MAXIMUM CLASS OF PROTECTION OF THE ENTIRE PPE BEING USED.
INSTRUCTIONS FOR USE
For hand protection, it is recommended that appropriate Salisbury insulating rubber
gloves must be used. For protection of insulating rubber gloves, Salisbury leather protectors
gloves must be used. For foot protection, Salisbury ASTM F1117 Dielectric is recommended.
Please contact Salisbury for further details.
DISCLAIMER: SELECTION OF PROPER PPE MUST BE BASED ON THE USER,
ENVIRONMENT AND APPLICATION AND IS THE SOLE RESPONSIBILITY OF
THE END USER. HONEYWELL SALISBURY IS NOT RESPONSIBLE FOR
ACCIDENTS, PROPERTY DAMAGE, INJURIES OR DEATH CAUSED BY USE OF
INAPPROPRIATE PPE AND/OR BY IMPROPER USE OF PPE.
Spare parts available for use with the Salisbury Prism Shield™ Plus Arc Flash
Protection Hoods:
Cap style hard hat: Part # N10R030000
Full brim style hard hat: Part # N20R460000
PP, AS1200FB-PP, AS1200U-PP and AS1200-MSA-PP
Replacement face shield for weight balancing shields 20 cal/cm²: Part # AS2000-PP,
AS2000FB-PP, AS2000U-PP and AS2000-MSA-PP
Replacement face shield for 8 to 12 Cal/cm² beekeeper style hoods: Part # 1200-PP
Replacement face shield for 20 to 40 Cal/cm² beekeeper style hoods: Part # 4000-PP
Replacement face shield for 65 to 100 Cal/cm² beekeeper style hoods: Part # 10000-PP
Replacement face shield for 20 Cal/cm² Lift front hoods: Part # LFH20FSA-PP
Replacement face shield for 20 Cal/cm² Lift front hoods: Part # LFH40FSA-PP
Safety eye wear: Part # 1011027HS are recommended
9
Advertisement
Table of Contents
