Configuration Guide; Set The Led Brightness; Program The Number Of Senders - Garnet SeeLeveL II 709 Series Installation Manual & User Manual

CONFIGURATION GUIDE

Set the LED Brightness

The LED brightness can be adjusted to suit the user and the operational
circumstances. If it is to be used in the service bay area where sunlight can reach
it, the LED brightness should be high.
1. To program the LED brightness, the
display needs to enter the brightness
programming mode. To do this, press and
hold down the BATT button, the display
will show the battery voltage.
2. Continue to hold down the BATT button,
press and hold the GREY button (use
the BLACK button for 709-2P). Continue
to hold down both buttons for about
5 seconds until the display shows
bri indicating brightness programming
mode. Then release both buttons.
3. The current brightness level is displayed.
b-1 is the minimum brightness and b-4 is
the maximum brightness.
4. Press the GREY tank button (use the
BLACK button for 709-2P) to increase
brightness, or the FRESH tank button to
decrease brightness.
5. When the display shows the correct
brightness, press the BATT button to exit
the programming mode.
SeeLeveL II 709 Series Display Manual
1 2 . 6
BATT
Hold LEVEL IN PERCENT
+
BATT GREY
Hold
Hold
b r i
LEVEL IN PERCENT
b - 1
b - 2
LEVEL IN PERCENT
LEVEL IN PERCENT
b - 3 b - 4
LEVEL IN PERCENT LEVEL IN PERCENT

GREY

FRESH
BATT

Program the Number of Senders

To program the number of senders for each tank, the display needs to enter
the sender programming mode. By default each tank is set for single sender
application. This should only be done at the time of installation; there is no
reason to change the number of senders afterward. Make sure that the number
of senders programmed into the display matches with the number of senders
connected; otherwise the display will show an error.
1. Press and hold down the button for the tank
to be programmed, the display may show a
level or an error message for that tank.
2. Continue to hold down the button for the
tank, and hold down the BATT button. The
display will show dIA (diagnostics). Continue
to hold down both buttons until the display
enters the programming mode, this should
take about 5 seconds (RV-C, BTP3, and N2K
models take about 10 seconds).
3. When the programming mode is entered, the
display will show FrS if entering the number
of senders for the fresh tank, GrS if entering
the Grey tank, or bLS if entering the black
tank. When this occurs release both buttons.
4. The display will show 1SE (one sender) or
2SE (two senders). This is what is currently
programmed into the display. These are the
only two options; the display will not work
with more than two senders per tank.
Note: For classic versions, 1 or 2 senders
are the only options, but for RV-C and BTP3
the options are 0, 1, or 2 senders. 0 senders
removes that tank from the RVC or bluetooth
data.
5. To change the number of senders, press the
tank button, each time the button is pressed
the display will toggle between 1SE and 2SE.
6. When the display shows the correct number
of senders, press the BATT button to save
any changes to exit the programming
mode. Each tank will need to be calibrated
individually using this procedure.
W CAUTION: For displays that have a GALLEY button the GREY and
GALLEY tanks can only have one sender per tank and cannot be stacked.
or or
FRESH GREY BLACK
Hold Hold Hold
D 1 A
+
BATT
LEVEL IN PERCENT
Hold
f r S G r S b L S
LEVEL IN PERCENT LEVEL IN PERCENT LEVEL IN PERCENT
Fresh Grey Black
1 5 E 2 5 E
LEVEL IN PERCENT LEVEL IN PERCENT
1 Sender 2 Senders
or or
FRESH GREY BLACK
BATT
Page 8