Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Advantech PCLD-8751
Summary of Contents for Advantech PCLD-8751
- Page 1 PCLD-8751/8761/8762 48-Channel Isolated D/I and Relay Board User Manual...
- Page 2 No part of this man- ual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reli- able.
- Page 3 Product Warranty (2 years) Advantech warrants to you, the original purchaser, that each of its prod- ucts will be free from defects in materials and workmanship for two years from the date of purchase. This warranty does not apply to any products which have been repaired or...
- Page 4 Step 1. Visit the Advantech web site at www.advantech.com/support where you can find the latest information about the product. Step 2. Contact your distributor, sales representative, or Advantech's cus- tomer service center for technical support if you need additional assistance. Please have the following information ready before...
-
Page 5: Table Of Contents
Contents Chapter 1 Introduction ............. 2 General Information ............2 Features ................2 Table 1.1:PCLD-8751/8761/8762 Channel Information 2 Chapter 2 Installation ............4 Initial Inspection..............4 2.1.1 Caution! ................ 4 Connectors and Jumpers............ 5 Chapter 3 Operations............18 Power Source Selection........... 18 Control Logic .............. - Page 6 PCLD-8751/8761/8762 User Manual...
-
Page 7: Chapter 1 Introduction
Introduction This chapter introduces PCLD-8751, PCLD-8761, and PCLD-8762. Sections include: • General Information • Features... - Page 8 1.2 Features • Works with Advantech TTL DI/O cards equipped with 48 digital input/ output channels on SCSI 68-pin cable connectors • 48 opto-isolated digital input/ relay output channels •...
- Page 9 Installation This chapter show how to install and configure PCLD-8751, PCLD-8761 & PCLD-8762. Sections include: • Initial Inspection • Connectors and Jumpers...
-
Page 10: Chapter 2 Installation
Chapter 2 Installation 2.1 Initial Inspection PCLD-8751, PCLD-8761 & PCLD-8762 are thoroughly inspected before being shipped. Before installing the board, make sure that everything has been included in the package. You should also inspect the board for any defects or damage that may have occurred during shipping. If you find anything missing, defective or damaged, contact your dealer immediately. -
Page 11: Connectors And Jumpers
2.2 Connectors and Jumpers 2.2.1 PCLD-8751 (48-Ch Isolated Digital Input Board) Chapter 2... - Page 12 CN1: SCSI 68-pin Connector PCLD-8751/8761/8762 User Manual...
- Page 13 TB1/TB2/TB3/TB4: Wiring Terminal Block Name Name Name Name PA00 1+,1- PB04 13+,13- PA10 25+,25- PB14 37+,37- PA01 2+,2- PB05 14+,14- PA11 26+,26- PB15 38+,38- PA02 3+,3- PB06 15+,15- PA12 27+,27- PB16 39+,39- PA03 4+,4- PB07 16+,16- PA13 28+,28- PB17 40+,40- PA04 5+,5- PC00...
- Page 14 The control logic is positive when pin1 and pin2 of JP1 are shorted. If pin2 and pin3 of JP1 are shorted, then the control logic becomes negative. The factory setting is positive control logic. (Also see Chapter 3.2) Jumper Setting Positive control logic. Negative control logic. Description (Default setting) PCLD-8751/8761/8762 User Manual...
- Page 15 2.2.2 PCLD-8761 (24-Ch Isolated DI and 24-Ch Relay Output Board) Chapter 2...
- Page 16 CN1: SCSI 68-pin Connector PCLD-8751/8761/8762 User Manual...
- Page 17 TB1/TB2/TB3/TB4: Wiring Terminal Block Name Name Name Name PA00 1+,1- PB04 13+, PA10 25COM,25 PB14 37COM,37 NC,25NO NC,37NO PA01 2+,2- PB05 14+, PA11 26COM,26 PB15 38COM,38 NC,26NO NC,38NO PA02 3+,3- PB06 15+, PA12 27COM,27 PB16 39COM,39 NC,27NO NC,39NO PA03 4+,4- PB07 16+, PA13...
- Page 18 If pin2 and pin3 are shorted, then the control logic becomes neg- ative. The factory setting is positive control logic. (Also see Chapter 3.2) JP1 (Isolated DI)/ JP2 (Relay Output) Jumper Setting Positive control logic. Negative control logic. Description (Default setting) PCLD-8751/8761/8762 User Manual...
- Page 19 JP3: Relay Driving Power Source Selection It is necessary to provide +5 V as the relay channels driving power source. And the power source can be selected as internal or external by JP3. The default setting of JP3 is an internal power source, which means +5V is provided from the PC.
- Page 20 2.2.3 PCLD-8762 (48-Channel Relay Output Board) PCLD-8751/8761/8762 User Manual...
- Page 21 CN1: SCSI 68-pin Connector Chapter 2...
- Page 22 The control logic is positive when pin1 and pin2 of JP1 are shorted. If pin2 and pin3 of JP1 are shorted, then the control logic becomes negative. The factory setting is positive control logic. (Also see Chapter 3.2) Jumper Setting Positive control logic. Negative control logic. Description (Default setting) PCLD-8751/8761/8762 User Manual...
-
Page 23: Chapter 3 Operations
Operations This chapter has information for oper- ating PCLD-8751, PCLD-8761 & PCLD-8762. Sections include: • Power Source Selection • Control Logic • Wiring... -
Page 24: Power Source Selection
When using the SCSI 68-pin connector, PCLD- 8751 and PCLD-8761 can be powered directly from the PCI bus by con- necting CN1 to any Advantech PC-LabCard product. It is also possible to connect external supplies to PCLD-8761 by connecting an external power supply to terminal TB7. -
Page 25: Wiring
3.3 Wiring 3.3.1 Isolated DI Wet Contact Dry Contact Chapter 3... - Page 26 Relay PCLD-8751/8761/8762 User Manual...
- Page 27 Specifications...
-
Page 28: Appendix A Specifications
PCLD-8762 285 x 121mm PCLD-8751 Max. +5 V @ < 0.6 A Power Consumption PCLD-8761 Max. +5 V @ < 1.6 A PCLD-8762 Max.+7V @ 1.8A +30V @ 0.45A Accepts #14 to #24 AWG wires Screw Terminal PCLD-8751/8761/8762 User Manual...