Unpacking, Moving, Use And Storage; Setting To Work - Connection To The Power Supply; Warning Labels; Extensions - Nilfisk-Advance VHS110 Z22 Instruction Manual

Unpacking, moving, use and storage

To unpack the vacuum unit, remove the retainers with a
hammer and a screwdriver.
Also remove the fastening devices placed by the manufacturer
when packing, by using suitable tools.
Release the wheel brakes and remove the machine from the
supporting platform, by using a ramp that can provide adequate
capacity, and by driving the vacuum cleaner by the handle.
Operate on flat, horizontal surfaces.
The load-bearing capacity of the surface the machine is placed
on must be suitable for bearing its weight.
If the device is to work in a fixed position, allow wide space
around the device in order to ensure freedom of the movement
and allow the maintenance staff to operate with ease.
CAUTION!
The manufacturer shall not be liable for any damages
caused to the machine during lifting, when the lifting
equipment supplied by the manufacturer is not used.
CAUTION!
When several supporting platforms are provided, the
supporting platform to which the machine is anchored
must be handled with a forklift truck that can provide
adequate capacity. Then unpack the machine by laying
it down on a flat and horizontal surface that can provide
adequate capacity for the vacuum cleaner weight.
Setting to work - connection to the power
supply
CAUTION!
■ Make sure there is no evident sign of damage to
the machine before starting work.
■ Before plugging the machine into the electrical
mains, make sure the voltage rating indicated on
the data plate corresponds to that of the electrical
mains.
■ Connect the plug into a socket with a correctly
installed ground contact/connection. Make sure
that the machine is turned off.
■ The plugs and connectors of the connection cables
must be protected against splashes of water.
■
Check that for proper connection to the electrical
mains.
■ Use the machine only when the cables that connect
to the electricity mains are in perfect condition
(damaged cables could lead to electric shocks!).
■
Regularly check there are no signs of damage,
excessive wear, cracks or ageing on the electric
cable.
CAUTION!
When the device is operating, do not:
■ Crush, pull, damage or tread on the cable that
connects to the electrical mains.
■
Only disconnect the cable from the electrical
mains by removing the plug (do not pull the cable).
■ Only replace the electric power cable with one of
the same type as the original: H07 RN-F, The same
rule applies if an extension is used.
■
The cable must be replaced by the manufacturer's
Service Centre staff or by equivalent qualified
personnel.
The system safety officers must:
■ Prevent any improper use or manoeuvre.
■ Make sure that the safety devices are not removed or
tampered with.
■ Check that all maintenance operations are regularly
performed;
■ Make sure that no machine part (couplings, holes, etc.) is
modified to attach additional devices;
■ Make sure that only original Nilfisk spare parts are used.
The user shall be responsible for ensuring that installation
complies with the all relevant local provisions. The
equipment must be installed by qualified technicians who
have read and understood the instructions herein.

Warning labels

Labels:
1.
Warning: Using an appropriate tester, check the grounding
continuity between the plug ground pin and the final
suction accessory.
2. Caution: Don't open while the voltage is applied.

Extensions

Extension cords are not allowed within a classified zone unless
marked accordingly.
CAUTION!
The vacuum cleaner's power socket must be protected
by a differential circuit-breaker with surge current
limitation that shuts off the power supply when the
current discharged to the ground exceeds 30 mA for 30
m/s or an equivalent protection circuit.
In case the socket that the vacuum cleaner is connected
to could exceed 1000 V in case of a surge generated
by a lightning, the user shall provide the appropriate
protection.
CAUTION!
Never spray water on the vacuum cleaner: this could
be dangerous for persons and could short circuit the
power supply.
7
VHS110 Z22
NOTE
Figure 3
GB
C421