Related Manuals for Wali GSDM003-P
Summary of Contents for Wali GSDM003-P
- Page 1 Triple Monitor Desk Mount 27" GSDM003-P 75x75/100x100 (1-7kg)x3 (2.2-15.4lbs)x3 RATED support@walielectric.com...
- Page 3 Supplied Parts List Monitor Arm VESA Plate C-Clamp A (x1) B (x1) C (x3) D (x1) Pole Wire Clip Grommet Base Plate Support Plate E (x1) F (x1) G (x1) H (x1) Anti-skid Pad Top Screw M6X16 Bolt 4mm Allen Key I (x1) J (x3) K (x3)
- Page 4 Step 2 Option A Clamp Installation 1. Loosen the bolts on C-clamp using 4mm Allen Key L . C-clamp Brace C-clamp 2. Connect Pole E and C-clamp Brace from the bottom using M6x16 Bolt and tighten with 4mm Allen Key Tear off the protective paper and attach Anti-Skid Pad I to the bottom designated position of C-Clamp Brace image shown.
- Page 5 3.1 For 0.4''- 2'' thick desk Loosen the Bolts on the C-Clamp Brace using 4mm Allen Key . Hang the C-Clamp on the bolts and tighten using 4mm Allen Key L . 0.4”-2” 3.2 For 1.8''- 3.3'' thick desk Loosen the screw to release the hand knob using a screwdriver as image shown. Turn over the bracket and tighten the screw.
- Page 6 Step 2 Option B Grommet Base Installation 1. Cut the Anti-skid Pad I along the broken line. Tear 2. Loosen the screw to release the hand knob off the protective paper and attach Anti-Skid Pad I to using a screwdriver as image shown. the bottom designated position of Grommet Base (Screwdriver not included ) Plate G as the image shown.
- Page 7 Step 3 WARNING: 1. Firmly hold the two halves of the spring arm together and have another person cut off the cable tie from around the spring arm. 2. Slowly release the pressure on the spring arm and allow it to gradually stretch to its full extension.
- Page 8 Step 5 Step 5.1 Step 5.2 Select Monitor Screws Select Spacers ( if needed ) Only one screw size fits your Monitor Hand thread screws into the threaded inserts on the back of your Monitor to determine which screw diameter (M4 or M5) to use.
- Page 9 Step 7 To properly balance the arm with monitors mounted, adjust the spring tension with Allen Key 6mm M. First, position and firmly hold the arm horizontally as shown. Ask for assistance should you require it. If the arm drops, turn the adjustment screw counter-clockwise until it stays in a horizontal position.
- Page 10 Step 8 Slide the cable slot covers towards the VESA plate direction to detach it off the arm. Guide the cable through the cable slot and put the cover back to the arm.
- Page 11 Step 9 Angle Adjustments Tilt: Adjust the VESA Plate tilt using 6mm Allen . (Tilt +35°/-35°) Note: If the display does not stop at your desired position, tighten the screws as shown. Swivel: Manually adjust swivel angle. Store the Allen Keys in the Wire Clip (swivel -90°/+90°) Rotate: Manually adjust rotate angle.
- Page 12 We support the technology that brings your home to life. We offer high quality products, professional customer service, and extensive technical support. If you have any questions,please contact us. support@walielectric.com 1-844-SATTLER (18447288537) www.walielectric.com...