Rielta FOTON-SH2-RK Installation Manual

WIRELESS PASSIVE INFRARED

1 Product Overview

Wireless passive infrared detector «Foton-SH2-RK» (hereinafter, the
Detector) is intended for detecting intrusion into a protected premises
through door or window openings and generating an alarm message.
The Detector highlights:
- transmitsion of status messages via two-way communication
channel by the «Rielta-Contact-R» protocol in the 433.05
frequency range to the control panel (hereinafter, CP) supporting the
«Rielta-Contact-R» wireless two-way data exchange protocol;
- case tamper protection;
- immunity to interference caused by small animals and ambient light.

2 Features of the Detector

- Dual-element pyrodetector.
- «Vertical curtain» detection zone.
- Temperature compensation of the detection sensitivity.
- The maximum Detector installation height is 5 m.
- Two-way installation using four fastening surfaces of the Detector
base: either above the protected opening, or in the corners of window
openings, door cases, etc.
- High resistance to ambient light – 12000 lx.
- Immunity to electromagnetic interference.
- Case tamper protection.
- Four possible operating frequencies available. The operating
frequency number is assigned automatically by the CP during the
binding process.
- Automaticl switching to the backup operating frequency in case
of challenging interference situation on the main one.

3 Specifications

Table 1
Features
Installation height
Types of detection zones
Radio exchange period
Operating temperature range
Dimensions
Weight
IP rating
Battery life (under normal
conditions and Radio exchange
period of at least 30 sec)
The Detector is powered by a СR123A type lithium battery (3 V).

4 Scope of Delivery

Each Detector unit package contains the items listed in Table 2.
Table 2
Name
Wireless passive infrared detector «Foton-SH2-RK»
Screw 3-3х30.016
Wall plug NAT 5х25 SORMAT
CR123А lithium power supply battery
Wireless passive infrared detector «Foton-SH2-RK». Installation
Guide

5 Informativity

The Detector ensures transmission and indication of the following
messages:
- «Alarm» – when a human is moving within the detection zone
across it's side border, within the speed range of 0.3 to 3 m/sec at
a distance of 3 m;
- «Tamper» – the Detector case is tampered;
- «Norm» – there are no other messages;
- «Low-battery» – under supply voltage reduces lower than 2,4
- «Communication quality» – the communication quality appraisal
is indicated;
- «Binding» – when the Detector is initialized in the system;
- «Identification» – by a relevant command from the CP.
DETECTOR
«FOTON-SH2-RK»
Installation Guide
434.79 MHz
—
Value
up to 5 m
continuous vertical curtain
from 10 sec to 10 min (programmed in
the process of binding with the repeater)
from minus 20 °C to +55 °C
maximum 80 x 47 x 42 mm
maximum 120 g
IP41
up to 5 years

6 Detection Pattern

7 LED Indication

Table 3
Detector Status
«Binding»
«Alarm»*
«Identification»
«Connection quality»
Binding procedure
completed
*) — Alarm indication is deactivated 15 min after the Detector cover is
closed and reactivated after it has been opened or by a command from
the CP.

8 Binding with the CP

The binding procedure is intended for logging of the Detector in the
CP and transmitting of service information to it.
Prepare the CP for the Detector binding in accordance to the CP
manual.
8.1 Adhering correct polarity install the СR123А power-supply
battery to the battery-contact clips located at the PCB opposite side
or remove isolator.
8.2 LED indicator blinking green displays the Detector readiness for
the binding procedure.
In case the LED indicator does not blink, close the «RESET» contacts
for a short period.
8.3 After a successful binding with the CP, the LED indicator lights
red for 2 sec.
8.4 The «Binding» procedure is limited to 100 sec. After it expires,
the Detector changes to the sleep mode. To resume the «Binding»
mode, the «Reset» contacts must be closed for a moment.

9 Choosing an Installation Place for the Detector

The Detector must be located in the radio-coverage zone of it's
CP. Therefore, it is advisable to appraise the quality of communication
with the repeater beforehand. The procedure of communication
quality appraising is described in the chapter «Communication Quality
Appraisal».
When choosing locations for the Detector installation, it is advisable
to take note of the fact that the detection zone may be limited by
QNT
non-transparent objects (curtains, curtain holders, door trims, etc.),
as well as glass partitions. There must be no air conditioners, space
1 pc.
heaters or heating radiators in the Detectors detection zone. The
2 pcs.
maximum Detector installation height is 5 m. The Detector installation
2 pcs.
options are shown in Figure 2.
1 pc.
1 copy

10 Communication Quality Appraisal

Before installing the Detector to it's place of operation, it is advisable
V;
to appraise the CP communication quality. Follow these steps.
-0,4
10.1 Prepare the Detector for operation and put it on it's place of
operation with a closed cover.
10.2 Open the Detector case, whereupon the Detector will indicate
the quality of CP communication.
90
о
10 m
Figure 1
LED Indication
LED Status
LED indicator blinks
green intermittently at
0.5 Hz frequency
LED indicator lights red
if indication is enabled
for at least 0.5 sec
LED indicators
blinks red and green
alternately at 1 Hz
frequency
See «Communication Quality Appraisal»
LED indicator lights red
for 2 sec
Till 5 m
6 m
Figure 2
5 m
11 о
Operation Mode
By a command from
the CP
8 m