Advertisement

Quick Links

TABLE OF CONTENTS

1 Specifications ----------------------------------------------------- 2
3 Troubleshooting Guide ----------------------------------------- 5
4.2. P.C.B. assy removal -------------------------------------- 7
4.3. Motor removal ---------------------------------------------- 9
4.4. Cord reel unit replacement -----------------------------10
4.6. Installation of some Pakkin----------------------------- 11
5 Wiring Connection Diagram ---------------------------------13
6 Exploded View and Replacement Parts List -----------14
6.1. EXPLODED VIEW (ATTACHMENTS) --------------14
6.2. PARTS LIST (ATTACHMENTS) ----------------------15
6.3. EXPLODED VIEW (BODY UNIT) --------------------16
6.4. PARTS LIST (BODY UNIT) ----------------------------17
6.5. PACKING INSTRUCTIONS----------------------------18
Model No.
Product Coior :Sherbet Blue
Destination
PAGE
6.6. PACKING LIST ------------------------------------------- 19
© 2007 Matsushita Electric Industrial Co., Ltd. All
rights reserved. Unauthorized copying and distribu-
tion is a violation of law.
Order No.VCB0707022CE
Vacuum Cleaner
MC-CL676-ZC79
:Europe
PAGE

Advertisement

Table of Contents
loading

Summary of Contents for Panasonic MC-CL676-ZC79

  • Page 1: Table Of Contents

    Order No.VCB0707022CE Vacuum Cleaner MC-CL676-ZC79 Model No. Product Coior :Sherbet Blue Destination :Europe TABLE OF CONTENTS PAGE PAGE 1 Specifications ----------------------------------------------------- 2 6.6. PACKING LIST ------------------------------------------- 19 2 Location of Controls and Components ------------------- 3 3 Troubleshooting Guide ----------------------------------------- 5 4 Disassembly and Assembly Instructions ---------------- 6 4.1.
  • Page 2: Specifications

    1 Specifications Model No. MC-CL676-ZC79 Power source 230V~50Hz Input power (MAX) 2300W Input power (Nominal) 2000W Power control Extension wand Telescopic Floor nozzle Turbin nozzle Dimensions (WxLxH)mm 290x470x280 Net weight 6.4kg Cleaning tools Crevice nozzle / Upholstery nozzle...
  • Page 3: Location Of Controls And Components

    2 Location of Controls and Components...
  • Page 5: Troubleshooting Guide

    3 Troubleshooting Guide CONDITION CHECKPOINT METHOD OF INSPECTION CAUSE / REMEDY Motor fails to rotate Power supply cord Check power supply cord continu- If there is no continuity, replace the ity. cord reel patition unit. Fuse of P.C.B. Ass’y Check fuse continuity. If there is no continuity, replace (250V, 13A) P.C.B.
  • Page 6: Disassembly And Assembly Instructions

    4 Disassembly and Assembly Instructions Important notice: Before replacing any components, make sure to turn OFF the vacuum cleaner. Remove the power plug from the outlet. 4.1. Separate the upper and lower 3. Remove the three screws fixing the upper and lower bod- ies.
  • Page 7: Assy Removal

    5. Remove the ornamental plate unit from the lower body. 8. Lift the upper body to separate it from the lower body. 6. Remove the screw fixing the caster unit (on the right in 4.2. P.C.B. assy removal the figure below) from the bottom of the lower body to remove the lower caster support plate, caster unit.
  • Page 8 2. Wiring treatment 4. Remove the P.C.B. assy from the P.C.B. holder. * When removing the P.C.B. assy, unhook it from the tab on the P.C.B. holder by spreading the holder frame. Note: When removing the P.C.B. assy, do not bend it to prevent damage and the wires from breaking.
  • Page 9: Motor Removal

    6. Disconnect the fast-on terminal of the lead wire connect- 3. Remove all components fitted to the fan motor unit. ing the P.C.B. assy to the body partition assy. a. Remove the motor support rubber (rear). b. Remove the motor support. c.
  • Page 10: Cord Reel Unit Replacement

    4.4. Cord reel unit replacement 2. Remove the screw fixing the body partition assy and the cord reel unit. 1. Lift the body partition assy (fitted with the cord reel unit) 3. Remove the cord reel unit from the body partition assy. while removing the cord reel shaft from the side of the lower body.
  • Page 11: Installation Of Some Pakkin

    4.6. Installation of some Pakkin 4.7. How to disassemble the tur- 1. Remove the two screws fixing the lower and front bodies. bine nozzle 4.7.1. Agitator ass'y 1. Rotate the Lock on the brush cover to unlock and remove the brush cover U. 2.
  • Page 12 4.7.2. Separation of the floor nozzle 4.7.4. Removal of the floor nozzle brush upper U from the floor nozzle CU.DU.EU.FU lower U 1. Turn the floor nozzle lower unit over. Insert the tip of a flat-blade screwdriver into the ditch in the brush installa- 1.

Table of Contents