Advertisement
Quick Links
24 VAC Universal Intermittent Pilot Gas Ignition Control
Quick Reference Guide
The C610U Universal Intermittent Pilot Gas Ignition Control module replaces many popular
flame rectification type of intermittent pilot ignition (IPI) modules, including those manufactured
by Honeywell, Robert Shaw, ICM, Fenwal, and Johnson Controls.
The following is an overview of the C610U series control, and is intended to only be used by
Certified Service Technicians.
APPLICATION
Gas Furnaces
Boilers
Water Heaters
Commercial Cooking
FEATURES
24 VAC microprocessor based IPI control
System diagnostics
32 Selectable preset timings of popular models
Universal flame sensing (Local/Internal or Remote/External)
Full time flame sensing
Flame sense test pins
4 mounting hole positions, 2 that match Honeywell and Fenwal
Built-in burner ground
Voltage/Frequency monitoring
©
2018 BASO Gas Products
Part No. BASO-INS-C610UQRG, Rev. C
24 VAC Universal Intermittent Pilot Gas Ignition Control
Installation Instructions
Issue Date
C610UQRG
June 28, 2018
1
www.baso.com
Advertisement
Related Manuals for Baso C610U Series
Summary of Contents for Baso C610U Series
- Page 1 (IPI) modules, including those manufactured by Honeywell, Robert Shaw, ICM, Fenwal, and Johnson Controls. The following is an overview of the C610U series control, and is intended to only be used by Certified Service Technicians.
-
Page 2: Specifications
AGENCY CERIFICATIONS UL 60370-1, UL 60730-2-5 File: M2926 Software conforms to UL60730 Requirement Component Recognized System (US & Canada) EN298:2012 File: 657989 24 VAC Universal Intermittent Pilot Gas Ignition Control © 2018 BASO Gas Products Part No. BASO-INS-C610UQRG, Rev. C www.baso.com... - Page 3 * If the existing system uses a burner ground wire, this can be attached to the 24V GND/BRN GND terminal using the supplied dual spade connector, or otherwise connected to the burner ground mounting tab. 24 VAC Universal Intermittent Pilot Gas Ignition Control © 2018 BASO Gas Products Part No. BASO-INS-C610UQRG, Rev. C www.baso.com...
-
Page 4: Setup And Adjustments
When replacing an existing ignition control with the C610U, refer to Table 2 for the correct DIP switch settings. For a complete list of the controls the C610U replaces, see the BASO C610U Installation Instructions available at www.baso.com. The following timing parameters may be set with the 5-postion DIP switch (see Table 2). - Page 5 NOTE: Configurations with a number of trials are 100% lockout after the trials are complete. All controls have a Quick Start and Re-ignition. 24 VAC Universal Intermittent Pilot Gas Ignition Control © 2018 BASO Gas Products Part No. BASO-INS-C610UQRG, Rev. C www.baso.com...
-
Page 6: Led Status And Troubleshooting
Excessive high temperatures can damage the ignition control and cause it to malfunction. Make sure the ambient temperature around the ignition does not exceed the rated temperature for the control. 24 VAC Universal Intermittent Pilot Gas Ignition Control © 2018 BASO Gas Products Part No. BASO-INS-C610UQRG, Rev. C www.baso.com... -
Page 7: Troubleshooting Guide
(13mm) in the flame. See figure 1. Dirty or corroded flame sensor Faulty flame sensor wiring Poor burner ground Note: For more information on BASO ignitions and other products, plus complete installation instructions, please visit us at www.baso.com. CORRECT FLAME TOO LOW... - Page 8 Figure 2: Microammeter Connection Important: Preventative maintenance programs are an important part of maintaining optimum and safe function of you BASO Products. For more maintenance information, refer to the "Setup and Adjustements" sectin of the complete installation instructions. Any attempt to repair this assembly voids the manufacturer's 2 year warranty. For a replacement control, contact the original equipment manufacturer or nearest BASO Gas Products distributer.