Download
Share
Print this page
STILLA Wattle 8x4 Assembly Instructions Manual
  1. Manuals
  2. Brands
  3. STILLA Manuals
  4. Garden Houses
  5. Wattle 8x4
  6. Assembly instructions manual

STILLA Wattle 8x4 Assembly Instructions Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
STILLA
ASSEMBLY INSTRUCTIONS
Wattle 8x4'
S3110
Every part needed to construct your shed is included inside the pack; cedar
panels, doors, windows, hardware kits & roof sheeting. Please ensure you fully
unpack all the parts & check against the parts checklist before contacting
customer service about anything you believe may be missing. Thank-you!

Advertisement

loading
Need help?

Need help?

Do you have a question about the Wattle 8x4 and is the answer not in the manual?

Questions and answers

Related Manuals for STILLA Wattle 8x4

Summary of Contents for STILLA Wattle 8x4

  • Page 1 STILLA ASSEMBLY INSTRUCTIONS Wattle 8x4’ S3110 Every part needed to construct your shed is included inside the pack; cedar panels, doors, windows, hardware kits & roof sheeting. Please ensure you fully unpack all the parts & check against the parts checklist before contacting...
  • Page 2 • If you are installing your shed on the Stilla heavy duty floor, this can be placed on unlevelled surfaces and levelled up by using the 100x100 stumps provided.
  • Page 3 Top Batten/Bottom Batten 1520mm 1520mm Chanel 8x4 Hardware Kit 8x4 Instruction Manual Stilla Cover Strip (If no floor option cut SCS to 1800mm and join) Floor Kit – Option Floor Frame - (Rebated Floor 70x38mm/Heavy Duty Floor 140x38mm) Part Code...
  • Page 4 8x4 Lean To – Option – Add Extra Screws Part Code Checked Part Description Verandah Rafter 1000x42x35mm Verandah Fascias 1100x75x20mm Verandah Roof Sheets 1150mm Beam 1520x70x35mm Verandah Beam 1520x140x35mm Verandah Posts 2400x90x90mm 8x4 Annex – Option – Add Extra Screws Part Code Checked Part Description...
  • Page 5 If no floor option was purchased, go to step 2.0 (Wall Assembly) STEP 1.0 FLOOR KIT 1.0 – FLOOR KIT PART CODE QTY DESCRIPTION End Plate 2484mm Single Joist 1124mm Double Joist 1124mm Floor Nog 460mm 100BS 100mm Batten screw (Heavy Duty Floor Only) 75mm Nail (Rebated Floor Only) 65HHS 65mm Hex Head Screw...
  • Page 6 STEP 1.1 FLOORING INSTALLATION 1.1 – FLOOR INSTALLATION PART CODE DESCRIPTION Floor Board 1798x800mm Floor Board 598x800mm Floor Board 1798x311mm Floor Board 598x311mm 50PS 50mm Philips Screw 1.1 – FLOOR SHEETS Fasten floor sheets to floor frame as shown below using 50PS - The x marked on the floor sheets do not line up with our Joists, disregard.
  • Page 7 STEP 2.0 WALL ASSEMBLY 2.0 - ASSEMBLY PARTS – WALL ASSEMBLY PART CODE QTY DESCRIPTION Front panel 1200mm Wall panel 65HHS 65mm Hex head screw If optional window was purchased, it can take the place of any 1200mm (12P) panel. 2.0 - ASSEMBLY –...
  • Page 8 STEP 2.1 WALL ASSEMBLY 2.1 - ASSEMBLY PARTS – WALL ASSEMBLY PART CODE QTY DESCRIPTION 1200mm Wall panel 65HHS 65mm Hex head screw 2.1 - ASSEMBLY – WALL ASSEMBLY Screw through 12P into 12P (Top, centre & bottom) using 3 x 65HHS, holding studs flush on the outside.
  • Page 9 STEP 2.2 WALL ASSEMBLY 2.2 - ASSEMBLY PARTS – WALL ASSEMBLY PART CODE QTY DESCRIPTION 1200mm Wall panel 65HHS 65mm Hex head screw 2.2 - ASSEMBLY – WALL ASSEMBLY Screw through 12P into 12P (Top, centre & bottom) using 3 x 65HHS, holding studs flush on the inside.
  • Page 10 STEP 2.3 WALL ASSEMBLY 2.3 - ASSEMBLY PARTS – WALL ASSEMBLY PART CODE QTY DESCRIPTION 1200mm Wall panel 65HHS 65mm Hex head screw 2.3 - ASSEMBLY – WALL ASSEMBLY Screw through 12P into 12P (top, centre & bottom) using 3 x 65HHS holding studs flush on the outside.
  • Page 11 STEP 2.4 WALL ASSEMBLY 2.4 - ASSEMBLY PARTS – WALL ASSEMBLY PART CODE QTY DESCRIPTION Front panel 65HHS 65mm Hex head screw 2.4 - ASSEMBLY – WALL ASSEMBLY Screw through FP into 12P (top, centre & bottom) using 65HHS holding studs flush on the outside.
  • Page 12 2 x 65HHS in centre stud. (Image 1) Turn one gable over. Position (SCS) Stilla branded cover strip flush with bottom cedar board and flush on each end. Nail through cover strip into gable using 40N. (Image 2) Position (FGS) front gable cover strip over join in front gable.
  • Page 13 STEP 2.6 FRONT GABLE ASSEMBLY 2.6 - ASSEMBLY PARTS – GABLE ASSEMBLY PART CODE QTY DESCRIPTION Assembled front gable Assembled back gable 65HHS 65mm Hex head screw 2.6- ASSEMBLY – GABLE ASSEMBLY Carefully position front gable in position ensuring tongue on wall goes into groove on gable. Fasten up through front panels using 2 x 65HHS either side.
  • Page 14 STEP 3.0 ROOF ASSEMBLY 3.0 - ASSEMBLY PARTS – ROOF ASSEMBLY PART CODE QTY DESCRIPTION Bottom batten Top batten Rafter 100BS 100mm Batten screw 3.0 - ASSEMBLY – ROOF ASSEMBLY Slide rafters (R) into checked out sections in battens (BB & TB). Fasten through BB & TB into R using 1 x 100BS per join.
  • Page 15 STEP 3.1 ROOF ASSEMBLY 3.1 - ASSEMBLY PARTS – ROOF ASSEMBLY PART CODE QTY DESCRIPTION 1480mm roof sheet 40RS 40mm Roof screw 25RS 25mm Roof screw 3.1 - ASSEMBLY – ROOF ASSEMBLY Lay roof frame on a hard surface. Position roof sheets (RS) flush at top and flush with end of roof battens.
  • Page 16 STEP 3.2 ROOF ASSEMBLY 3.2 - ASSEMBLY PARTS – ROOF ASSEMBLY PART CODE QTY DESCRIPTION 40RS 40mm Roof screw 25RS 25mm Roof screw 3.2 - ASSEMBLY – ROOF ASSEMBLY Fasten either side of roof sheeting overlap at top and through joined rib at bottom. Bent up edge at top.
  • Page 17 STEP 3.3 ROOF ASSEMBLY 3.3 - ASSEMBLY PARTS – ROOF ASSEMBLY PART CODE QTY DESCRIPTION 40RS 40mm Roof screw 25RS 25mm Roof screw 3.3 - ASSEMBLY – ROOF ASSEMBLY Complete screwing roof off at top. 1 x 25RS in pan beside every rib. Once top complete screw bottom off using 1 x 40RS in every rib.
  • Page 18 STEP 3.4 ROOF ASSEMBLY 3.4 - ASSEMBLY PARTS – ROOF ASSEMBLY PART CODE QTY DESCRIPTION 1520mm Chanel Self-tapping screw 3.4 - ASSEMBLY – ROOF ASSEMBLY Slide capping onto roof overhang. Fasten capping (C) to roof using 3 x ST. Bent up edge at top Repeat steps 3.0 –...
  • Page 19 STEP 3.5 ROOF INSTALLATION 3.5 - ASSEMBLY PARTS – ROOF INSTALLATION PART CODE QTY DESCRIPTION Completed roof panels 65HHS 65mm Hex head screw 3.5 - ASSEMBLY – ROOF INSTALLATION Slide one roof panel into position. Ensure roof rafters are flush with gables on the inside. Top batten of roof frame is to be in line with gable peak.
  • Page 20 STEP 3.7 DOOR HEAD ASSEMBLY 3.7 - ASSEMBLY PARTS – DOOR HEAD ASSEMBLY PART CODE QTY DESCRIPTION Door Head 65HHS 65mm Hex Head Screws 3.7 - ASSEMBLY PARTS – DOOR HEAD ASSEMBLY Place door head in position under front gable between front panels – fasten in place. If Double door option was chosen go to step 4.2 STEP 3.8 DOOR HINGE ASSEMBLY...
  • Page 21 STEP 3.9 DOOR INSTALLATION 3.9 - ASSEMBLY PARTS –DOOR INSTALLATION PART CODE DESCRIPTION Door Hinge screw 3.9 - ASSEMBLY –DOOR INSTALLATION Hold door in position, 3mm down from top. Front of the door when closed will be flush with front of VJ cladding. Screw through hinge into front wall (as pictured).
  • Page 22 STEP 4.0 DOOR HANDLE ASSEMBLY 4.0 - ASSEMBLY PARTS – DOOR HANDLE ASSEMBLY PART CODE QTY DESCRIPTION T Handle 4.0 - ASSEMBLY – DOOR HANDLE ASSEMBLY Remove bolts and leaver from back of T Handle (TH). Mark and drill 12mm centre hole in position shown, 50mm in from door edge.
  • Page 23 If Double door option was not chosen please go to step 4.7 STEP 4.2 DOUBLE DOOR HINGE ASSEMBLY 4.2 - ASSEMBLY PARTS – DOUBLE DOOR HINGE ASSEMBLY PART CODE DESCRIPTION Hinge Hinge Screw Doors 4.2 - ASSEMBLY – DOUBLE DOOR HINGE ASSEMBLY Place door on back and hold hinge (H) in position.
  • Page 24 STEP 4.3 DOUBLE DOOR INSTALLATION 4.3 - ASSEMBLY PARTS – DOUBLE DOOR INSTALLATION PART CODE DESCRIPTION Doors Hinge screw 4.3 - ASSEMBLY – DOUBLE DOOR INSTALLATION Hold door in position, 3mm down from top. Front of the door when closed will be flush with front of VJ cladding.
  • Page 25 STEP 4.4 PAD BOLT INSALLATION 4.4 - ASSEMBLY PARTS – PAD BOLT INSTALLATION PART CODE DESCRIPTION Pad bolt Hinge Screw 4.4 - ASSEMBLY – PAD BOLT INSTALLATION Hold PB in position and fasten to door. Mark centre of bolt and drill 12mm hole in marked closed position.
  • Page 26 STEP 4.6 DOOR HANDLE ASSEMBLY 4.6 - ASSEMBLY PARTS – DOOR HANDLE ASSEMBLY PART CODE QTY DESCRIPTION T Handle Leaver Packer Hinge screw 4.6 - ASSEMBLY – DOOR HANDLE ASSEMBLY Holding DP in position, fasten to door (door with pad bolts) Holding door in closed position, flush with other door - slide leaver onto T Handle and tighten once hitting packer on fixed door.
  • Page 27 STEP 4.7 FASTENING WALLS TO FLOOR 4.7 - ASSEMBLY PARTS – FASTENING WALLS TO FLOOR PART CODE QTY DESCRIPTION 65HHS 65mm hex head screw 4.7 - ASSEMBLY – FASTENING WALLS TO FLOOR Ensure walls are in correct position and straight. Fasten through wall bottom plate in position shown below.
  • Page 28 STEP 5.0 CORNER POST ASSEMBLY Before nailing each corner posts on we recommend running a bead of silicone down these two lines as per images below. 5.0 - ASSEMBLY PARTS – CORNER POST ASSEMBLY PART CODE QTY DESCRIPTION 1890mm Corner post’s 40mm Nail 5.0 - ASSEMBLY –...
  • Page 29 STEP 5.1 COVER STRIP ASSEMBLY Before nailing cover strips on we recommend running a bead of silicone down this join as per images below. 5.1 - ASSEMBLY PARTS – COVER STRIP ASSEMBLY PART CODE QTY DESCRIPTION 1890mm Cover strip 40mm Nail 5.1 - ASSEMBLY –...
  • Page 30 STEP 5.2 FASCIA ASSEMBLY 5.2 - ASSEMBLY PARTS – FASCIA ASSEMBLY PART CODE QTY DESCRIPTION Fascia 40mm Nail 5.2 - ASSEMBLY – FASCIA ASSEMBLY Hold fascia’s in position. Flush with bottom of battens and meeting evenly at the top. Nail into end of Battens.
  • Page 31 STEP 5.3 RIDGE CAP INSTALLATION 5.3 - ASSEMBLY PARTS – RIDGE CAP INSTALLATION PART CODE QTY DESCRIPTION 1520mm Ridge Cap 40RS 40mm Roof screw 5.3 - ASSEMBLY – RIDGE CAP INSTALLATION Slide ridge cap into position. Make sure peak of ridge cap is in line with peak of fascia’s. Screw through ridge cap into 2 rib in from end and through into batten.
  • Page 32 STEP 5.4 8’ LOFT SHELF If you did not purchase this item, please skip this step. 5.4 - ASSEMBLY PARTS – 8’ LOFT SHELF PART CODE QTY DESCRIPTION 8’ Loft shelf 65HHS 65mm Hex head screw Shelf Support 5.4/ - ASSEMBLY – 8’ LOFT SHELF Holding loft shelf in position screw up through support plate into wall frame at each corner.
  • Page 33 STEP 6.0 LEAN TO / ANNEX If you did not purchase this option please skip this step 6.0 - ASSEMBLY PARTS – LEAN TO / ANNEX PART CODE QTY DESCRIPTION Verandah beam Batten Verandah rafter 75mm Nail 6.0 - ASSEMBLY – LEAN TO / ANNEX Nail through B &...
  • Page 34 STEP 6.1 LEAN TO / ANNEX 6.1 - ASSEMBLY PARTS – LEAN TO / ANNEX PART CODE QTY DESCRIPTION Verandah roof sheeting 40RS 40mm roof screw 25RS 25mm roof screw 6.1 - ASSEMBLY – LEAN TO / ANNEX Screw roof sheeting to frame using 2 x 25RS at top and 2 x 40RS at bottom. Note that the top screws go into the pan of the roof sheet and the bottom screws go into the rib of the roof sheet.
  • Page 35 STEP 6.2 LEAN TO / ANNEX 6.2 - ASSEMBLY PARTS – LEAN TO / ANNEX PART CODE QTY DESCRIPTION Verandah roof sheeting 40RS 40mm roof screw 25RS 25mm roof screw 6.2 - ASSEMBLY – LEAN TO / ANNEX Place the remaining 3 roof sheets in position and finish screwing off the top and bottom using 25RS in every pan at the top and 40RS in every rib at the bottom.
  • Page 36 STEP 6.3 LEAN TO / ANNEX 6.3 - ASSEMBLY PARTS – LEAN TO / ANNEX PART CODE QTY DESCRIPTION Verandah posts 100BS 100mm batten screw 65HHS 65mm hex head screw 6.3 - ASSEMBLY – LEAN TO / ANNEX Using 3 people, butt the verandah roof hard up under shed roof as shown in picture. Support front of verandah roof while fastening through frame into shed wall studs using 4 x 100BS.
  • Page 37 STEP 6.4 LEAN TO / ANNEX 6.4 - ASSEMBLY PARTS – LEAN TO / ANNEX PART CODE QTY DESCRIPTION Verandah fascia 40mm nail 6.4 - ASSEMBLY – LEAN TO / ANNEX Once fascia’s are on shed, trim lean-to/annex fascia to butt in and finish correctly. Nail through fascia using 4 x 40N per fascia.

  • Page 38: Product Maintenance

    TO REGISTER YOUR WARRANTY Thank-you for purchasing a STILLA product. To register your 10 year product warranty, please go to www.stilla.com.au/warranty and complete the online form. We recommend that you complete this step once you have finished installing your product.
  • Page 39 38 | P a g e...
  • Page 40 SHOW US YOUR SHED We would love to see a photo of your STILLA product installed in your backyard. Please upload this image when completing the warranty registration. Alternatively, you can send the photos by email to sales@stilla.com.au. If you require any assistance, please feel free to call or email.

This manual is also suitable for:

S3110