Newport 1936-R Series Startup Manual

Newport 1936-R Series Startup Manual

Single and dual-channel optical meters
Hide thumbs Also See for 1936-R Series:

Advertisement

Quick Links

Model 1936-R/2936-R Series
Single and Dual-Channel Optical
Meters
Start Up Guide

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 1936-R Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Newport 1936-R Series

  • Page 1 Model 1936-R/2936-R Series Single and Dual-Channel Optical Meters Start Up Guide...
  • Page 3 Enjoy your new instrument! First printing 2010 © 2010 by Newport Corporation, Irvine, CA. All rights reserved. No part of this start up guide may be reproduced or copied without the prior written approval of Newport Corporation. This start up guide has been provided for information only and product specifications are subject to change without notice.
  • Page 4 This page intentionally left blank...
  • Page 5: Safety Precautions

    Safety Precautions Please carefully read the following important safety precautions prior to unpacking and operating this equipment. In addition, please refer to the complete User’s Manual for additional important notes and cautionary statements regarding the use and operation of the equipment. Symbols and Definitions The following are definitions of symbols that are used throughout this Start Up Guide to call your attention to important information regarding your...
  • Page 6: General Cautions

    Start Up Guide  To avoid fire hazard, use only the specified fuse(s) with the correct type number, voltage and current ratings as referenced in the appropriate locations in the service instructions or on the equipment. Only qualified service personnel should replace fuses. ...
  • Page 7 Inspect the box for external signs of damage or mishandling. Inspect the contents for damage. If there is visible damage to the instrument upon receipt, inform the shipping company and Newport Corporation immediately. WARNING Do not attempt to operate this equipment if there is evidence of shipping damage or you suspect the unit is damaged.
  • Page 8: Electrical Requirements

    Start Up Guide Provide adequate distance between the 1936-R/2936-R Series Optical Power Meters and adjacent walls for ventilation purposes. Approximately 2-inch spacing for all surfaces is adequate. Electrical Requirements Before attempting to power up the unit for the first time, the following precautions must be followed: WARNING To avoid electrical shock hazard, connect the instrument to...
  • Page 9: System Start-Up

    System Start Up Startup Procedure WARNING To avoid electrical shock hazard, connect the instrument to properly earth-grounded, 3-prong receptacles only. Failure to observe this precaution can result in severe injury. Provided that the power meter has been installed in an appropriate environment and its power cord is connected to a working electrical outlet, power-up the power meter by pressing the power button on the lower left corner of the front panel.
  • Page 10: Rear Panel Layout

    Start Up Guide 2.2.1 Understanding the Main Screen The main screen is displayed after startup. The middle portion of the main screen is a real-time display of power measured in last used units, and the lower half of the main screen is a row of four labels for actions that the keys below them will activate.
  • Page 11 Start Up Guide  BNC Analog Output, Channel B (2936-R)  BNC Trigger Output, Channel B (2936-R)  BNC Trigger Input  USB (Universal Serial Bus) Device  9-Pin D-Sub RS-232 Figure 3 2936-R Rear Panel Layout The rear panel also has an AC input power connector (IPC) with a standard three-prong socket and voltage setting switch.
  • Page 12 CAUTION There are no user-serviceable parts inside the power meter. Work performed inside the power meter by persons not Authorized by Newport may void the warranty. WARNING To avoid electrical shock hazard, connect the instrument to properly earth-grounded, 3-prong receptacles only. Failure to observe this precaution can result in severe injury.
  • Page 13: Firmware Upgrade Procedure

    1.1.5.1. Note that these versions may not be the latest at the time you are performing a firmware upgrade. New firmware files may be available either through the Newport web site (http://www.newport.com) at the product page or through your local Newport application specialist.
  • Page 14 Start Up Guide This page is intentionally left blank...
  • Page 15: Maintenance, Service And Support

    Calibration accuracy is warranted for a period of one year. After one year, the unit should be returned to Newport Corporation for recalibration and NIST trace ability re-certification. To obtain information regarding factory service, contact Newport Corporation’s Service Department or your Newport representative.
  • Page 16 Number (RMA#). Return the product to Newport Corporation, freight prepaid, clearly marked with the RMA# and we will either repair or replace it at our discretion. Newport is not responsible for damage occurring in transit and is not obligated to accept products returned without an RMA#.
  • Page 18 Newport Corporation Worldwide Headquarters 1791 Deere Avenue Irvine, CA 92606 (In U.S.): 800-222-6440 Tel: 949-863-3144 Fax: 949-253-1680 Internet: sales@newport.com Visit Newport Online at: www.newport.com...

This manual is also suitable for:

2936-r series

Table of Contents