Technical Data - Parkside PMTS 210 A1 Operating And Safety Instructions Manual

15. Use only saw blades that are marked with an equal or
higher rotational speed than that marked on the power
tool.
16. Use only saw blades recommended by the manufacturer
which conform to EN 847-1, if intended for cutting wood
or similar materials.
17. Wear suitable personal protective equipment, such as:
- Hearing protection;
- Protective gloves when handling saw blades.
18. Only use saw blades recommended by the manufacturer
which conform to EN 847-1. Warning! When changing
the saw blade, ensure that the cutting width is not smaller
and the width of the saw blade disc is not greater than the
thickness of the riving knife!
19. When sawing wood and plastics, avoid the saw teeth
overheating. Reduce the feed speed in order to avoid the
plastic melting.
20. Please note that complex non-through cutting operations
and tapered cuts are not permitted.
21. Avoid bevel ripping on bevelling side of the saw blade.
Residual risks
The power tool is state-of-the-art and has been
built according to the recognised technical safety
regulations. However, individual residual risks can
arise during operation.
• Health hazard due to electrical power, with the use of im-
proper electrical connection cables.
• Furthermore, despite all precautions having been met, some
non-obvious residual risks may still remain.
• Residual risks can be minimised if the "safety instructions"
and the "Proper use" are observed along with the whole of
the operating instructions.
• Do not unnecessary stress the machine: too much pressure
when sawing will damage the saw blade quickly. This results
in reduced output of the machine in the processing and in
cut precision.
• Avoid accidental starting of the machine: Do not press the
on/off switch when inserting the plug into the socket.
• Use the tool that is recommended in this manual. In doing so,
your saw provides optimal performance.
• Keep your hands away from the working area when the ma-
chine is in operation.
• Before performing setting or maintenance work, switch the
device off and unplug the mains plug.
8 GB/IE

7. Technical data

AC motor...................................................... 220-240 V∼ 50 Hz
Power consumption ........................................ 1200 watts (S1*)
Idle speed n ............................................................... 4800 rpm
0
Hard metal saw blade ..........................ø 210 x ø 30 x 2.6 mm
Number of teeth .......................................................................24
Riving knife thickness ........................................................2.0 mm
Min. size of workpiece W x L x H .................. 10 x 50 x 1 mm
Table size without table width extension ...........485 x 445 mm
Min. table size with table width extension ........485 x 515 mm
Max. table size with table width extension .......485 x 630 mm
Max. cutting height at 45° ..............................................45 mm
Max. cutting height at 0° .................................................48 mm
Tilting saw blade ......................................................... 0-45° left
Extraction connection .................................................... ø 35 mm
Weight .................................................................. approx. 14 kg
Machine size (with extension)
W x L x H ................................................. 485 x 630 x 440 mm
*S1:Continuous operation with constant load
**S6 25 %:
Continuous duty with intermittent loading (operating time 10 min.)
In order avoid impermissible overheating of the motor, the mo-
tor should be driven for only 25 % of the operating time with
the stipulated nominal power and must then continue to run
with no load for the remaining 75 % of the operating time.
Noise
The noise values have been determined in accordance with
EN 62841.
Sound pressure level L ............................................ 87.5 dB(A)
pA
Uncertainty K ......................................................................3 dB
pA
Sound power level L ............................................100.5 dB(A)
WA
Uncertainty K .....................................................................3 dB
WA
Wear hearing protection.
Excessive noise can result in a loss of hearing. Total vibration
values (vector sum of three directions) determined according
to EN 62841.
NOTE:
The specified device emissions values have been measured in
accordance with a standardised test procedure and can be
used for comparison of one power tool with another.
The specified device emissions values can also be used for an
initial estimation of the load.
WARNING:
The noise emission values can vary from the specified values
during the actual use of the power tool. This depends on the
type and the manner in which the power tool is used, and in
particular the type of workpiece being processed. Implement
measures to protect against noise nuisance. In doing so, take
into account the complete working process, including the times
when the power tool is working without load or switched off.
1500 watts (S6 25 %**)