Subscribe to Our Youtube Channel
Related Manuals for Kramer VM-3S
Summary of Contents for Kramer VM-3S
-
Page 1: User Manual
KRAMER ELECTRONICS, Ltd. USER MANUAL Video/Audio Distribution Amplifiers Models: VM-3S/ VM-3Sxl VM-3V/ VM-3Vxl IMPORTANT: Before proceeding, please read paragraph entitled "Unpacking and Contents" KRAMER ELECTRONICS LTD. -
Page 2: Table Of Contents
Factors Affecting Quality of Results SPECIFICATIONS HOW DO I GET STARTED UNPACKING AND CONTENTS Optional Accessories VM SERIES AMPLIFIERS Getting To Know Your VM-3S/xl Amplifier Getting To Know Your VM-3V/xl Amplifier INSTALLATION CONNECTING TO VIDEO DEVICES USING VM VIDEO/AUDIO AMPLIFIERS Turning on the Amplifier... -
Page 3: Introduction
In addition to the Kramer line of high quality amplifiers, such as the one you have just purchased, Kramer also offers a full line of high quality switchers, processors, interfaces, controllers and computer-related products. This manual includes configuration, operation and option information for the following products from the Kramer VM-3 line of distribution amplifiers. -
Page 4: Specifications
SPECIFICATIONS VM-3S / VM-3Sxl Function 1:3 s-Video DA Input 1 s-Video, 1Vpp/75ohm (Y), 0.3Vpp/75ohm (C) on a 4P connector Output Type 3 s-Video, 1Vpp/75ohm (Y), 0.3Vpp/75ohm (C) on 4P connectors Output Coupling Controls Termination Switch (VM-3Sxl only) S/N Ratio 70dB (80 dB for VM-3Sxl) Video Bandwidth 60 MHz -3dB (Y);... -
Page 5: How Do I Get Started
For best results the 104L amplifier is installed adjacent to the video source. The 104L is housed in the compact KRAMER TOOLS enclosure and is fed by a 12VDC source. High bandwidth and front accessible controls make it suitable for the most demanding analog and SDI studio applications. - Page 6 611T/611R - (611T full bandwidth Fiber Optic Transmitter and 611R matching Fiber Optic Receiver) Part of the KRAMER TOOLS series, and designed for studio and other demanding applications, these machines, in combination, may be used to send one of the distributed channels to distances of 5-25Km. The 611T and 611R use state-of-the-art fiber optic circuitry and allow the user (via rear panel trimmers) to adjust input and output video levels and high frequency peaking to achieve best performance.
-
Page 7: Vm Series Amplifiers
The VM-3S/xl splits a single input source into three identical outputs with no discernible signal degradation. Video output and input signals are AC coupled for maximal flexibility. The VM-3S/xl receives external 12VDC feed, and is housed in a very compact enclosure, making it ideal for field use. -
Page 8: Getting To Know Your Vm-3V/Xl Amplifier
Getting To Know Your VM-3V/xl Amplifier The KRAMER VM-3V/xl is a full bandwidth, state-of-the-art, 1:3 video distribution amplifier designed for studio and other demanding applications. The VM-3V/xl splits a single input source into three identical outputs with no discernible signal degradation. Video output and input signals are AC coupled for maximal flexibility. -
Page 9: Installation
Video sources and output devices (such as amplifiers or recorders) may be connected to the amplifier through the BNC connectors (VM-3V model) or 4p type connectors (VM-3S model) located at the back of the machine. If looping is needed, the VM-3Sxl and VM-3Vxl should be used. For looping (allowing another amplifier or any video acceptor to use the same video input) use a “T”... - Page 10 NOTE Do not use excessively long cables if possible, as signal quality may degrade rapidly. Figure 3: Installing a VM Amplifier in a Video System KRAMER ELECTRONICS LTD.
-
Page 11: Taking Care Of Your Video Amplifier
If not, disconnect power source from the machine and reconnect again to reset the machine. 2. If the following recommended actions still do not result in satisfactory operation, please consult your KRAMER Dealer. Power And Indicators 10.1 Problem... - Page 12 Low frequency hum in the interconnection, including your video cables. output signal Check the following to remove hum bars: KRAMER ELECTRONICS LTD. WARNING! Do not disconnect the ground from any piece of video equipment in your signal path! Confirm that all interconnected equipment is connected to the same phase of power, if possible.
-
Page 13: Limited Warranty
3) Shipping charges. HOW YOU CAN GET WARRANTY SERVICE 1) To obtain service on you product, you must take or ship it prepaid to any authorized Kramer service center. 2) Whenever warranty service is required, the original dated invoice (or a copy) must be presented as proof of warranty coverage, and should be included in any shipment of the product. - Page 14 EXCLUSION OF DAMAGES Kramer’s liability for any defective products is limited to the repair or replacement of the product at our option. Kramer shall not be liable for: 1) Damage to other property caused by defects in this product, damages based upon inconvenience, loss of use of the product, loss of time, commercial loss;...
- Page 15 For the latest information on our products and a list of Kramer distributors, visit our Web site: www.kramerelectronics.com. Updates to this user manual may be found at http://www.kramerelectronics.com/manuals.html. We welcome your questions, comments and feedback. Kramer Electronics, Ltd. Web site: www.kramerelectronics.com E-mail: info@kramerel.com...
Need help?
Do you have a question about the VM-3S and is the answer not in the manual?
Questions and answers