Related Manuals for Rittal SK 3138000
Summary of Contents for Rittal SK 3138000
- Page 1 Roof-mounted fan SK 3138000 SK 3140110 SK 3139100 SK 3140140 SK 3139110 SK 3140500 SK 3140100 SK 3140510 Assembly and installation instructions...
-
Page 2: Table Of Contents
4.1.2 Connection data 4.1.3 Overvoltage protection and supply line load 12 4.1.4 PE conductor connection 4.1.5 Installing the power supply Installing the pilot wire Commissioning Inspection and maintenance Storage and disposal Technical specifications Accessories Warranty Customer services addresses Rittal roof-mounted fan... -
Page 3: Safety Instructions
Safety instructions Intended use – Assembly, installation and servicing may only be performed Rittal roof-mounted fans were developed and designed in accord- by properly trained specialists. ance with the state of the art and the recognised rules governing – Do not obstruct the air inlet and air outlet of the roof-mounted technical safety. -
Page 4: Product Description
2. Product description Components Cover Fan plate with fan Inflow nozzle for air routing Base tray with pleated filter Electrical connector Fig. 1: Components Rittal roof-mounted fan... -
Page 5: Scope Of Supply
Scope of supply Description Illustration Qty. Annotation Roof-mounted fan Pleated filter pre-installed Dachlüfter Roof-mounted fan Ventilateur de toit Assembly and installation instructions Montage- und Installationsanleitung Assembly and installation instructions Notice de montage et d'installation Connector Tab. 1: Scope of supply Rittal roof-mounted fan... -
Page 6: Function
2.3.3 Filter mats The roof-mounted fan is supplied with four pleated filters (class ePM10 50% to ISO 16890) pre-installed. The filter must be checked regularly depending on the level of dust exposure, and replaced as necessary. Rittal roof-mounted fan... -
Page 7: Mounting
IP 21 and UL Type 1. vibrations and oscillations. ◾ Use only original Rittal filters which bear the Rittal logo to be – Appropriate measures to decouple vibration must be taken in sure of the protection category, air throughout and approvals. -
Page 8: Installing The Roof-Mounted Fan
3. Mounting Installing the roof-mounted fan 3.3.1 Installation IP 21 CLICK! CLICK! Rittal roof-mounted fan... -
Page 9: Additional Installation Steps: Installation From Outside Ip 54/Ul Type 12
3. Mounting Installing the roof-mounted fan 3.3.2 Additional installation steps: Installation from outside IP 54/UL Type 12 ¼ TX25 TX25 = max. 2 Nm (4x) ¼ TX25 Rittal roof-mounted fan... -
Page 10: Additional Installation Steps: Installation From Inside Ip 54/Ul Type 12
3. Mounting Installing the roof-mounted fan 3.3.3 Additional installation steps: Installation from inside IP 54/UL Type 12 TX25 = max. 2 Nm (4x) 3.3.4 Additional installation steps: Enhanced protection category IP 55/UL Type 12 Rittal roof-mounted fan... -
Page 11: Additional Installation Steps: Protection Category Ip 21/Ul Type 1 And Higher Air Throughput
3. Mounting Installing the roof-mounted fan 3.3.5 Additional installation steps: Protection category IP 21/UL Type 1 and higher air throughput Rittal roof-mounted fan... -
Page 12: Electrical Connection
– If no wire end ferrules are used, strip the individual wires by max. 9 mm (observe the applicable clearances and creepage distances). ◾ Connect the connector to the roof-mounted fan from below. Rittal roof-mounted fan... - Page 13 Connecting the power supply 4.1.5 Installing the power supply SK 3139100/SK 3139110/ SK 3140140 SK 3140100/SK 3140110 / 1 2 L N PE max. 9 mm Strain relief SK 3140500/SK 3140510 Fig. 2: Connection diagrams Fig. 3: Connector and strain relief Rittal roof-mounted fan...
-
Page 14: Installing The Pilot Wire
0 – 10 V/ Fig. 4: Pilot wire Max. speed (as delivered, with jumper between the "+10 V" and "0 – 10 V/PWM" connections. Adjustable speed Adjustable speed via PWM 1 – 10 kHz Adjustable speed via potentiometer Rittal roof-mounted fan... -
Page 15: Commissioning
Check the noise generation of the fan. 7. Storage and disposal The roof-mounted fan must be stored at a temperature within the range specified in the technical data. Disposal can be entrusted to the Rittal factory. Please call for further information. Rittal roof-mounted fan... -
Page 16: Technical Specifications
8. Technical specifications Technical specifications Unit SK 3138000 SK 3139100 SK 3139110 SK 3140100 SK 3140110 SK 3140140 SK 3140500 SK 3140510 Electrical specifications 380…415, 3~, 50/60 without fan 220…240, 115, 1~, 220…240, 115, 1~, 220…240, 115, 1~, Rated operating voltage... -
Page 17: Accessories
9. Accessories Pleated filter Filter class in accordance with To fit Model No. Packs of Model No. DIN EN 779 ISO 16890 SK 3138000, SK 3139100, SK 3139110, SK 3140100, ePM10 50 % 12 pc(s). SK 3174120 SK 3140110, SK 3140140, SK 3140500, SK 3140510 Tab. 4: Pleated filter Chopped-fibre filter Filter class in accordance with To fit Model No. - Page 18 Model No. SK 3140500, SK 3140510 1 pc(s). SK 3235440 Tab. 11: Control unit for speed control Outlet filter To fit Model No. Packs of Model No. SK 3138000, SK 3139100, SK 3139110, SK 3140100, SK 3140110, SK 3140140, SK 3140500, 1 pc(s). SK 3243200 SK 3140510 Tab. 12: Outlet filter Rittal roof-mounted fan...
-
Page 19: Warranty
10. Warranty The conditions named in the sales and delivery conditions of the associated Rittal agents and subsidiaries apply. 11. Customer services addresses Headquarters Germany Service HUB China RITTAL GmbH & Co. KG RITTAL Electro-Mechanical Technology Co. Ltd. Auf dem Stuetzelberg No. - Page 20 Rittal roof-mounted fan...
- Page 21 Notes Rittal roof-mounted fan...
- Page 22 ◾ Climate Control ◾ IT Infrastructure ◾ Software & Services You can find the contact details of all Rittal companies throughout the world here. www.rittal.com/contact RITTAL GmbH & Co. KG Auf dem Stuetzelberg · 35745 Herborn · Germany Phone +49 2772 505-0...