Leds; Connectors - Ublox EVK-R8 Series User Manual

1.4 LEDs

Function
Main power
Cellular VCC
Cellular native USB
Cellular two UARTs USB
Cellular USB
Cellular USB / UART
Cellular UART detach
Cellular RS232 / UART
Cellular RI indicator
Cellular CTS indicator
Cellular GPIO1 indicator
Cellular GPIO2 indicator
Cellular GPIO3 indicator
Cellular GPIO4 indicator
GNSS time pulse
GNSS supply
GNSS USB
GNSS time pulse
Cellular / GNSS DDC
Table 2: EVK-R8 LED descriptions

1.5 Connectors

Function
9 - 18 V Power Input
SIM card holder
Cellular antenna
GNSS antenna
Cellular native USB
Cellular two UARTs USB
Cellular USB (UART)
Cellular RS232 (UART)
DIL B2B headers
Cellular headset
GNSS antenna
GNSS USB
GNSS backup battery
GND
Table 3: EVK-R8 connector descriptions
⚠
Caution! In the unlikely event of a failure in the internal protection circuitry, there is a risk of an explosion
when charging a fully or partially discharged battery. Replace the battery when it no longer has a
sufficient charge for unit operation. Check the battery before use if the device has not been used for an
extended period of time.
⚠
Caution! Risk of explosion if battery is replaced with incorrect type. Dispose battery according to rules!
UBX-22018774 - R01
C1-Public
Description
Power supply plugged in the 9 - 18 V Power Input
Cellular module supplied. Main power switch must be switched on
USB cable plugged in the Cellular native USB connector
USB cable plugged in the Cellular two UARTs USB connector
USB cable plugged in the Cellular USB connector for UART access
Green light is activated when UART is routed to the cellular USB connector
Red light blinks at UART TX or RX data on the Cellular USB connector
UART signals are available only on the DIL connector on ADP-R8 board
Green light is activated when UART is routed to Cellular RS232 connector
Red light blinks at UART TX or RX data on the Cellular RS232 connector
RI line turns ON (active low)
CTS line turns ON (active low)
Green light is activated when cellular GPIO1 is high
Green light is activated when cellular GPIO2 is high
Green light is activated when cellular GPIO3 is high
Green light is activated when cellular GPIO4 is high
Time pulse of the LENA-R8001M10 GNSS system
Supply of the GNSS module mounted on the ADP-GNSS is turned ON
USB cable plugged in GNSS USB connector
Time pulse of the GNSS module mounted on the ADP-GNSS
Cellular / GNSS module communication over the DDC (I2C) interface
Description
Connector for the AC / DC power adapter of the EVK
AC: 100-240 V, 0.8 A, 50-60 Hz / DC: +12 V, 2.5 A
SIM card holder
SMA connector for the cellular antenna (ANT, Tx/Rx)
SMA connector for LENA-R8001M10 GNSS system (ANT_GNSS, Rx)
Mini USB connector for the cellular native USB interface
Mini USB connector for the cellular main and auxiliary USB interfaces
Mini USB connector for the cellular UART interface converted as USB interface
DB9 connector for the cellular UART interface converted as RS232 interface
Dual-In-Line Board-to-Board connectors for LENA-R8 interfaces
Audio headset jack connector for the cellular audio interface
SMA connector for the antenna of the GNSS module mounted on ADP-GNSS
Mini USB connector for the GNSS module USB interface
Backup battery socket for the GNSS module (under GNSS adapter board)
Ground terminals for the probe reference
IEC 60417-5172
Class II equipment
Starting up
EVK-R8 - User guide
LED # Board Color
DL401 EVB
DL400 EVB
LED700 ADP-R8
LED600 ADP-R8
DL501 EVB
DL403 EVB
DL404 EVB
DL405 EVB
DS501 EVB
DS500 EVB
DS107 EVB
DS105 EVB
DS109 EVB
DS103 EVB
LED701 ADP-R8
DS118 ADP-GNSS
DS124 ADP-GNSS
DS121 ADP-GNSS
DS132 ADP-GNSS
Name Board
J400 EVB
J300 EVB
J500 ADP-R8
J501 ADP-R8
J700 ADP-R8
J600 ADP-R8
J501 EVB
J500 EVB
J402-J403 ADP-R8
J303 EVB
J208 ADP-GNSS
J102 ADP-GNSS
BT200 EVB
J402÷J406 EVB
Page 7 of 20