ekwb EK-Quantum Vector2 FE RTX 4090 D-RGB ABP Set User Manual
Gpu water block
Hide thumbs
Also See for EK-Quantum Vector2 FE RTX 4090 D-RGB ABP Set:
- Manual (21 pages) ,
- User manual (21 pages) ,
- User manual (20 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for ekwb EK-Quantum Vector2 FE RTX 4090 D-RGB ABP Set
Summary of Contents for ekwb EK-Quantum Vector2 FE RTX 4090 D-RGB ABP Set
- Page 1 EK-Quantum Vector² FE RTX 4090 D-RGB ABP Set GPU WATER BLOCK USER GUIDE...
- Page 2 Please note the installation of the product is intended to be undertaken by an adequately trained and experienced person. You are installing the product at your own risk. If you are not properly trained or experienced or feel unsure about the installation procedure, please refrain from installing the product yourself and contact our tech support for assistance.
-
Page 3: Table Of Contents
TABLE OF CONTENTS BOX CONTENTS WATER BLOCK DIMENSIONS TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS NICKEL PLEXI NICKEL ACETAL PREPARING THE GRAPHICS CARD REMOVING THE STOCK COOLER PREPARING THE WATER BLOCK FOR INSTALLATION CUTTING AND PLACING THERMAL PADS APPLYING THERMAL COMPOUND ATTACHING THE WATER BLOCK ATTACHING THE ACTIVE BACKPLATE FITTINGS AND TUBING... -
Page 4: Box Contents
BOX CONTENTS EAN: 105871 M2.5x4 AX1 Screw (7 pcs) M2.5x8 AX1 Screw (1 pc) Standoff Ø4.5/2.5 (1 pc) EK-Quantum Vector FE RTX 4090 D-RGB ABP Set M3x10 AX1 Screw (1 pc) Polyamid Washer M2.5 0.5mm (7 pcs) Standoff M2.5-M3 x 6.6mm (1 pc) Quantum Plug (2 pcs) Nut M2.5 (2 pcs) Terminal OR - Vector... -
Page 5: Water Block Dimensions
WATER BLOCK DIMENSIONS 236.3 mm 123.9 mm 95.9 mm 35.5 mm 41 mm - 5 -... -
Page 6: Technical Specifications And Water Block Parts
TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS NICKEL PLEXI - Dimensions: (L x H x W): 236.3 x 148 x 41 mm - D-RGB LED count: 28 - D-RGB cable length: 50 cm - D-RGB connector 3-pin 5V digital LED header Position Description Quantity... -
Page 7: Nickel Acetal
NICKEL ACETAL - Dimensions: (L x H x W): 236.3 x 148 x 41 mm - D-RGB LED count: 28 - D-RGB cable length: 50 cm - D-RGB connector 3-pin 5V digital LED header Position Description Quantity 105849 Coldplate (Nickel) 105851 Top plate (Acetal) 8533... -
Page 8: Preparing The Graphics Card
PREPARING THE GRAPHICS CARD STEP 1 REMOVING THE STOCK COOLER Place your graphics card on the flat surface and carefully remove the stock cooler. Do not forget to unplug all the LED and fan connectors. Pay attention to the following steps when installing the EK-Quantum Vector FE RTX 4090 water block onto your graphics card. - Page 9 STEP 2 Carefully remove the complete active backplate with the terminal. ACTIVE BACKPLATE Additional two (2) O-rings 14 x 1 EPDM50 needs to be removed. TERMINAL O-RING 14x1 mm STEP 2 STEP 3 M2.5-M3x6.6 STANDOFF Unscrew four (4) M2.5-M3 x 6.6 standoffs with the provided tool (EK-Plug out Spludger Tool).
-
Page 10: Cutting And Placing Thermal Pads
CUTTING AND PLACING THERMAL PADS STEP 1 Thermal Pad F – 1.0 mm (120 x 16 mm) The GPU water block comes with thermal pads that have to be cut into smaller pieces to cover all the VRM components, such as COILs, MOSFETs, and drivers. -
Page 11: Applying Thermal Compound
APPLYING THERMAL COMPOUND STEP 1 Apply the enclosed thermal grease (thermal compound) on the GPU heat spreader – IHS – as shown in the image. The layer of the thermal compound must be thin and even over the entire surface of the IHS. - Page 12 STEP 2 Use five (5) M2.5 x 4 AX1 screws and PVC washers to tighten the GPU PCB. Tighten the screws evenly using the Phillips-head screwdriver. EK recommends you start tightening the screws M2.5 x 4 AX1 around the GPU core first and then continuing outward to prevent M2.5 PVC SCREW damaging the GPU.
-
Page 13: Attaching The Active Backplate
STEP 3 M2.5-M3 x 6.6 After securing the GPU PCB, position the replacement I/O Bracket STANDOFF and four (4) M2.5-M3 x 6.6 standoffs. Tighten it with the provided tool (EK-Plug out Spludger Tool). BRACKET For this step, you will need: EK-Plug Out Spludger Tool STEP 3 ATTACHING THE ACTIVE BACKPLATE... - Page 14 STEP 2 ACTIVE BACKPLATE Insert two (2) O-rings (14 x 1 mm) into slots on the cold plate. Then carefully place the active backplate on standoffs as shown in the image. While putting the active backplate on the PCB, make sure the O-rings stay in the slots.
-
Page 15: Fittings And Tubing
FITTINGS AND TUBING STEP 1 Screw in two (2) G1/4 threaded male fittings. Attach the liquid cooling tubes and connect the water block to the cooling loop. Do not forget to plug the remaining two openings using EK- PLUG G1/4 the enclosed EK-Plug G1/4 or its equivalent. -
Page 16: Connecting The D-Rgb Led Strip
CONNECTING THE D-RGB LED STRIP STEP 1 Plug the 3-pin connector of the distribution plate D-RGB LED light to the D-RGB HEADER on the motherboard. The LED will work if the pin layout on the header is as follows: +5V, Digital, Empty, Ground. -
Page 17: Warranty
Removing the label will void the leak-free guarantee, but not the guarantee on the product itself. Any other RMA issues can be reported to EK Customer Support at www.ekwb.com/support for further analysis. - 17 -... -
Page 18: Support And Service
SUPPORT AND SERVICE In case you need assistance or wish to order spare parts or a new mounting mechanism, please contact: https://www.ekwb.com/customer-support/ For spare parts orders, refer to the page with “TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS” where you can find the EAN number of each part you might need.
Need help?
Do you have a question about the EK-Quantum Vector2 FE RTX 4090 D-RGB ABP Set and is the answer not in the manual?
Questions and answers