ekwb EK-Quantum Vector2 AMP/Trinity RTX 4090 ABP Set D-RGB User Manual

Gpu water block
Hide thumbs Also See for EK-Quantum Vector2 AMP/Trinity RTX 4090 ABP Set D-RGB:

Advertisement

Quick Links

EK-Quantum
Vector² AMP/Trinity RTX 4090 ABP Set D-RGB
GPU WATER BLOCK
USER GUIDE

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the EK-Quantum Vector2 AMP/Trinity RTX 4090 ABP Set D-RGB and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for ekwb EK-Quantum Vector2 AMP/Trinity RTX 4090 ABP Set D-RGB

  • Page 1 EK-Quantum Vector² AMP/Trinity RTX 4090 ABP Set D-RGB GPU WATER BLOCK USER GUIDE...
  • Page 2 Please note the installation of the product is intended to be undertaken by an adequately trained and experienced person. You are installing the product at your own risk. If you are not properly trained or experienced or feel unsure about the installation procedure, please refrain from installing the product yourself and contact our tech support for assistance.
  • Page 3: Table Of Contents

    TABLE OF CONTENTS BOX CONTENTS WATER BLOCK DIMENSIONS TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS NICKEL PLEXI PREPARING THE GRAPHICS CARD REMOVING THE STOCK COOLER ZOTAC GAMING GeForce RTX 4090 AMP Extreme AIRO PREPARING THE WATER BLOCK FOR INSTALLATION CUTTING AND PLACING THERMAL PADS APPLYING THERMAL COMPOUND ATTACHING THE WATER BLOCK CUTTING AND PLACING THERMAL PADS...
  • Page 4: Box Contents

    BOX CONTENTS EAN: 106123 M2.5x4 AX1 Screw (5 pcs) M2.5x8 AX1 Screw (1 pc) M2.5x6 AX1 Screw (2 pcs) EK-Quantum Vector AMP/Trinity RTX 4090 Polyamid Washer M2.5 0.5mm Standoff M2.5-M3 x 6.6mm ABP Set D-RGB M3x10 AX1 Screw (1 pc) (7 pcs) (1 pc) Thermal Pad F 0.5 mm...
  • Page 5: Water Block Dimensions

    WATER BLOCK DIMENSIONS 272.5 mm 124 mm 73.5 mm 41 mm 35.5 mm - 5 -...
  • Page 6: Technical Specifications And Water Block Parts

    TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS NICKEL PLEXI - Dimensions: (L x H x W): 272.5 x 155 x 41 mm - D-RGB LED count: 15 - D-RGB cable length: 50 cm - D-RGB connector 3-pin 5V digital LED header (Pinout: +5V | Data | Blocked | Ground) Position Description...
  • Page 7: Preparing The Graphics Card

    PREPARING THE GRAPHICS CARD REMOVING THE STOCK COOLER STOCK COOLER ZOTAC GAMING GeForce RTX 4090 AMP Extreme AIRO STEP 1 Using a Philips-head screwdriver, unscrew marked screws to detach the stock cooler and retention bracket from the GPU PCB. After removing, carefully unplug all the LEDs and FANs cables.
  • Page 8: Preparing The Water Block For Installation

    PREPARING THE WATER BLOCK FOR INSTALLATION STEP 1 First, remove the terminal badge which is attached to the terminal with two magnets. Under the badge, unscrew three (3) screws M3 x 10 AX1 SCREW M4 x 20 DIN7984. Additional seven (7) screws M3 x 10 AX1 need to be removed (as shown in the image).
  • Page 9 STEP 2 Carefully remove the complete active backplate with the terminal. ACTIVE BACKPLATE Additional two (2) O-rings 14 x 1 mm needs to be removed. TERMINAL OR 14 x 1 mm STEP 2 STEP 3 Unscrew seven (7) M2.5-M3 x 6.6 standoffs with the provided tool (EK-Plug out Spludger Tool).
  • Page 10: Cutting And Placing Thermal Pads

    CUTTING AND PLACING THERMAL PADS STEP 1 Thermal Pad F – 0.5 mm (120 x 16 mm) The GPU water block comes with thermal pads that have to be cut into smaller pieces to cover all the VRM components, such as COILs, 0.5 mm 120 mm MOSFETs, and drivers.
  • Page 11: Applying Thermal Compound

    APPLYING THERMAL COMPOUND STEP 1 Apply the enclosed thermal grease (thermal compound) on the GPU heat spreader – IHS – as shown in the image. The layer of the thermal compound must be thin and even over the entire surface of the IHS.
  • Page 12 STEP 2 M2.5 x 6 AX1 SCREW Use five (5) M2.5 x 4 AX1 Screws and PVC washers to tighten the PCB on the water block. Tighten the screws evenly using the M2.5 x 4 AX1 SCREW Phillips-head screwdriver. EK recommends you start tightening the screws around the GPU core first, and then continuing outward to M2.5 PVC WASHER prevent damage to the GPU.
  • Page 13: Cutting And Placing Thermal Pads

    STEP 3 After securing the GPU PCB, position the seven (7) M2.5-M3 x 6.6 standoffs. Tighten it with the provided tool (EK-Plug out Spludger Tool). M2.5-M3 x 6.6 STANDOFF For this step, you will need: EK-Plug Out Spludger Tool STEP 3 CUTTING AND PLACING THERMAL PADS STEP 1 Thermal Pad F –...
  • Page 14 G1.5 G1.5 Thermal Pad - 120 x 24 x 1.0 mm Thermal Pad - 120 x 24 x 1.5 mm G1.5 Thermal Pad - 120 x 24 x 2.0 mm STEP 1 STEP 2 Insert two (2) O-rings (14 x 1 mm) into slots on the cold plate. Then ACTIVE BACKPLATE carefully place the active backplate on standoffs (as shown in the image).
  • Page 15: Fittings And Tubing

    STEP 3 M3 x 10 AX1 SCREW Place seven (7) M3 x 10 AX1 screws into the water block standoffs and tighten them using a Philips head screwdriver (as shown in the image). After attaching the AX1 Screws, three (3) terminal screws M4 x 20 DIN7984 need to be attached using Allen Key 2.5 mm.
  • Page 16: Inserting The Graphics Card Into The Chassis

    INSERTING THE GRAPHICS CARD INTO THE CHASSIS Carefully lift your graphics card with the installed water block and insert it into your PC’s motherboard PCI Express expansion slot. Please keep in mind that your graphics card is heavier than before it was equipped with the water block.
  • Page 17: Testing The Loop

    Removing the label will void the leak-free guarantee, but not the guarantee on the product itself. Any other RMA issues can be reported to EK Customer Support at www.ekwb.com/support for further analysis. - 17 -...
  • Page 18: Support And Service

    SUPPORT AND SERVICE In case you need assistance or wish to order spare parts or a new mounting mechanism, please contact: https://www.ekwb.com/customer-support/ For spare parts orders, refer to the page with “TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS” where you can find the EAN number of each part you might need.

This manual is also suitable for:

3831109902608

Table of Contents