Install Custom Door Panels; Install New Water Line; Connect Water Supply - KitchenAid KSBP25IVSS Installation Instructions Manual

Install Custom Door Panels

1. Remove any packing tape.
2. Remove the refrigerator and freezer door trims from the hinge
side of each door by pulling the trim away from the bottom of
the door first.
3. Partially unscrew the two screws that hold the top trim in
place. It is not necessary to completely remove the screws.
Loosen the screws at least " (6.35 mm) from the trim to allow
the panels to slide freely.
4. Remove the existing door panels, if panels were provided.
5. Slide custom door panels into place.
NOTE: The door panels may require
fillers behind the panels to keep them from being loose in that
area.
6. Replace the hinge side trims by inserting the notched end
under the top trim first.
7. Tighten the two top trim screws.
B
C
A
D
C
A. Side trims
B. Top trim screws

Install New Water Line

(if required)
TOOLS NEEDED:
Flat-blade screwdriver
" and " Open-end or
two adjustable wrenches
1. Turn OFF main water supply. Turn ON nearest faucet long
enough to clear line of water.
2. Find a " (12.70 mm) to 1 " (3.18 cm) vertical COLD water
pipe near the refrigerator.
NOTE: Horizontal pipe will work, but the following procedure
must be followed: Drill on the top side of the pipe, not the
bottom. This will help keep water away from the drill. This also
keeps normal sediment from collecting in the valve.
3. Determine the length of copper tubing you need. Measure
from the connection on the lower left rear of refrigerator to the
water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use
(6.35 mm) O.D. (outside diameter) copper tubing. Be sure both
ends of copper tubing are cut square.
" (3.18 mm) cardboard
C. Door panels
D. Filler panels
" Drill bit
Hand drill or electric drill
(properly grounded)
"
4. Using a grounded drill, drill a
water pipe you have selected.
G
A. Cold water pipe
B. Pipe clamp
C. Copper tubing
D. Compression nut
5. Fasten shutoff valve to cold water pipe with pipe clamp. Be
sure outlet end is solidly in the
water pipe and that washer is under the pipe clamp. Tighten
packing nut. Tighten the pipe clamp screws carefully and
evenly so washer makes a watertight seal. Do not overtighten
or you may crush the copper tubing, especially if soft (coiled)
B
copper tubing is used. Now you are ready to connect the
copper tubing.
C
6. Slip compression sleeve and compression nut on copper
tubing as shown in the diagram. Insert the end of the tubing
into the outlet end of the shutoff valve as far as it will go.
Screw the compression nut onto the outlet end with an
A
adjustable wrench. Do not overtighten.
7. Place the free end of the tubing into a container or sink, turn
ON main water supply and flush out tubing until water is clear.
Turn OFF the shutoff valve on the water pipe.
D

Connect Water Supply

Style 1 - Connection to Water Valve
1. Unplug refrigerator or disconnect power.
2. Before attaching copper tubing to refrigerator, flush at least
2 qt (1.9 L) of water through the copper tubing and into a
bucket to get rid of any particles in the water line.
3. Check for leaks around the saddle valve. Do not overtighten
clamp or sleeve. This will crush copper tubing.
4. Attach the copper tube to the valve inlet using a compression
nut and sleeve as shown. Tighten the compression nut. Do not
overtighten.
5. Use the tube clamp on the back of the refrigerator to secure
the tubing to the refrigerator as shown. This will help prevent
damage to the tubing when the refrigerator is pushed back
against the wall.
6. Turn shutoff valve ON.
7. Check for leaks. Tighten any connections (including
connections at the valve) or nuts that leak.
A. Tube clamp
B. Copper tubing
8. The ice maker is equipped with a built-in water strainer. If your
water conditions require a second water strainer, install it in
the " (6.35 mm) water line at either tube connection. Obtain
a water strainer from your nearest appliance dealer.
" (6.35 mm) hole in the cold
A
B
C
F E D
E. Compression sleeve
F. Shutoff valve
G. Packing nut
" (6.35 mm) drilled hole in the
A
B
C
D
C. Compression nut
D. Valve inlet
7