DELTA DORE DRIVER 610 User Manual

DRIVER 610 - 620 - 611 - 621
Pilot wire programmer 1 or 2 zones
DRIVER
User guide
www.deltadore.com
• Carefully read these instructions prior to use.
• Do not attempt to repair the unit yourself ;
after-sales service is available.
• The following options are only available on the
DRIVER 611 or 621.
TYPHONE 500
When associated with the DRIVER 611 or 621, the
TYPHONE 500 allows you to control your heating
remotely by telephone.
MINOR 500
Regulates an underfl oor heating or radiant ceiling
heating system. In combination with the DRIVER 611
or 621, this unit is used to control the set points and
determine the room temperature measured by each
probe.
Because of changes in standards and equipment, the characteristics given in
the text and the illustrations of this document are not binding unless confi rmed
by our services.
Timer mode
This mode is used to select a mode for a given
time and for one zone only.
Example : comfort from 11h to 13h30.
0h 6h 8h 11h 13h30 17h
Information button
AUTO
During the , or modes, press the
If MINOR 500 option Si option MINOR 500
Temperature
measured
by the sensor
Indication of a sensor or
sensors on the installation
Description
DRIVER
Selector
dial
position
Continuous mode
Shutdown mode
Absence mode Time setting
Timer mode Programming
Automatic mode
Automatic mode
Turn the selector dial to AUTO.
Override
In automatic mode, override is used to go from Comfort to Economy mode (or conversely) until the next program change.
Example: it is 15:30 and you would like to switch to
Comfort mode before the set time (17:00).
0h 6h 8h 15h30
Override
3
3 3
3 3
1
1
1
1
1
1 1 1
1
23h 0h
2 2
2 2
2
Choice of the zone Selection of the Comfort
proposed on the or Economy mode.
DRIVER 620 or 621 Confi rm.
(the other zone follows
the AUTO mode).
Confi rm.
i
button repeatedly to fi nd out:
N° sensor
1
Time setting
Turn the selector dial to
The days fl ash.
Press + or - to change the day, then press OK to
Modifi cation
confi rm and continue on to the next setting.
buttons
To leave the "setting the time" mode, turn the
selector dial.
Selector dial
1
1
NOTE : If the unit is confi gured for a daily program,
the days setting is not offered.
DRIVER 610 or 611
follows the programming.
Current day
Room
temperature
17h 23h 0h
Press the override button
of zone 1.
To cancel the current override, press the button once more.
72:00
72:00 72:00
3
3
3
1 3 3
00:15 00:15 00:15
4 4
4 4
4
6 6
6
Adjustment of the duration
from 15 minutes to 72 hours
(in increments of 15 minutes).
Confi rmation and start of the
countdown
Absence mode
This mode lets you place your home under Frost
protection if you need to leave for several days.
Turn the selector dial to
Adjustment of the number of days (1 to 365).
Example : for a departure on 10th March and a return
on 18th March, program 8 days of absence.
Automatic operation will resume on 18 March at
midnight.
1 1
1
.
7 23
2 4
7 23 59
1 0
2 4 6
1 0 0
3 5
3 5 7
8
Current
Time
mode
Override
Information
button
At 17:00, the program will
Current override on
return to its usual program.
zone 1
72:00
72:00
5
5
5
5
00:15
00:15
6
Return to AUTO
6
mode at the end of
the countdown
.
365
365
2
365
1
2
1
3
3
Confi rm and start the
calendar countdown.
To cancel the current absence
mode, turn the selector dial.
59
6
0
7
8
DRIVER 620 or 621 follows the
programming in both zones.
5
1
2
1
3
Countdown
Décompte S18 00:00
Décompte Return to AUTO mode at S18 00:00
Dé
the end of the countdown