Sierra Wireless MC5720 Quick Start Manual
Hide thumbs
Also See for MC5720:
- Hardware integration manual (39 pages) ,
- Hardware integration manual (30 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Sierra Wireless MC5720
Summary of Contents for Sierra Wireless MC5720
- Page 1 Mini Card Universal Development Kit Quick Start Guide 2 1 3 0 6 7 7 R E V 1 . 1 C...
- Page 2 Limitation of liability The information in this manual is subject to change without notice and does not represent a commitment on the part of Sierra Wireless. SIERRA WIRELESS AND ITS AFFILIATES SPECIFICALLY DISCLAIM LIABILITY FOR ANY AND ALL DIRECT, INDIRECT, SPECIAL, GENERAL, INCIDENTAL,...
- Page 3 Fax: 1-604-231-1109 www.sierrawireless.com Web: For up-to-date product descriptions, documentation, application notes, firmware upgrades, troubleshooting tips, and press releases: www.sierrawireless.com To obtain the schematics for this device, contact your Sierra Wireless FAE and refer to Item #2500083. 1 .1C Apr- 06...
-
Page 4: Table Of Contents
M i n i C a r d U n i ve r s a l D e v e l opment Kit Quick Start Guide Table of contents Introduction ........................5 Required Equipment ......................5 Setup and installation ....................6 Hardware setup.........................6 Insert a USIM card (UMTS modules only).............6 Insert the Mini Card ....................7... -
Page 5: Introduction
In tr od uction Introduction This quick start guide explains how to set up the hardware and software components of Sierra Wireless’ Universal Development Kit (UDK) for use with: • CDMA modules – MC5720, MC5725 • UMTS modules – MC8755/8755V, MC8765/8765V, MC8775... -
Page 6: Setup And Installation
M i n i C a r d U n i ve r s a l D e v e l opment Kit Quick Start Guide Setup and installation To begin using the UDK with your development system, you need to: Set up the hardware •... -
Page 7: Insert The Mini Card
S e t up a nd i ns ta l la t ion 3. Insert the USIM card with its circuitry facing the daughterboard – line up the notch in the card with the notch in the slot. 4. Close the USIM casing. Insert the Mini Card After inserting the USIM card, insert the Mini Card: 1. -
Page 8: Remove/Replace The Mini Card
M i n i C a r d U n i ve r s a l D e v e l opment Kit Quick Start Guide 4. Push and hold the module down when it is firmly seated in the slot and then fasten it using the screws removed in Step 2. - Page 9 S e t up a nd i ns ta l la t ion 2. Screw the silver adapter onto the daughterboard’s main antenna connector. 3. Connect the Mini Card’s main antenna to the daughterboard’s main antenna connector using the gray wire provided – press down lightly on the connector ends (the first few times you use these connectors, they may be quite snug –...
-
Page 10: Connect The Power Supply And Usb Cable
M i n i C a r d U n i ve r s a l D e v e l opment Kit Quick Start Guide Connect the power supply and USB cable To install the power supply and USB cable: 1. - Page 11 S e t up a nd i ns ta l la t ion Table 2: SW200 Audio switch (installed on daughterboards used for voice- enabled modules) Function Dip1 Dip2 Dip3 Dip4 +20 dB mic path gain Unity gain mic path gain Disable mic connection Differential mic input Single-ended mic input...
-
Page 12: Install/Update Drivers
Install drivers for CDMA modules (MC57xx) 1. Download the installation package as instructed by your Sierra Wireless FAE. 2. If you have installed earlier versions of the Sierra Wireless drivers, you must remove them before continuing: Start > Settings > Control Panel Start >... -
Page 13: Install Drivers For Umts Modules (Mc87Xx)
Uninstall g. Click to confirm that the device is to be uninstalled. This removes all of the Sierra Wireless drivers listed in Step 4. DriverInstaller.exe 3. Locate and run – it is in the Software\DriverInstaller Start > Run folder. -
Page 14: Install Watcher
Sierra Wireless EVDO Watcher. c. Select Change/Remove d. Click 2. Download the installation file indicated by your Sierra Wireless FAE – this is a .zip file. launch.exe 3. Install Watcher – unzip the file and then run . The 3G Wireless Module screen appears. -
Page 15: Install Watcher For Umts Modules (Mc87Xx)
Double-click Sierra Wireless 3G Watcher. c. Select Change/Remove d. Click 2. Download the installation file indicated by your Sierra Wireless FAE – this is an .msi file. .msi 3. Install Watcher – run the file. The Watcher installation Welcome window appears.
Need help?
Do you have a question about the MC5720 and is the answer not in the manual?
Questions and answers