Extraordinary Maintenance - Ecowood FI 3 DUAL Installation, User’s And Maintenance Handbook

FI 3 FI 4
DUAL -
UK
ADVANCED PROGRAMMING INSTRUCTIONS
only to be carried out by technical staff
To enter advanced programming mode in order to modify the factory settings start by
pressing MAN/AUTO followed by the + button, then release them simultaneously.
The red light will come on to show you are adjusting pellet loading rate.
The letter A will appear to show that you can modify pellet loading rate at the ignition
stage.The setting (positioned in the centre of the scale) is shown on the display by the yel-
low LED's.
Use the + and - buttons to change the values.The ON/OFF button is used to confirm the
change and to change the sector for which the preset loading rate is to be modified.
After the letter A the pellet loading rates will appear in sequence 1-2-3-4-5, while the num-
ber 6 indicates the working time of the motor reducer.
At the end of this sequence the red light will go off and at the same time the green light will
go on to show that you are about to adjust the exhaust flue exhauster motor parameters,
then the following will appear in sequence: the letter A (ignition) and subsequently by press-
ing the ON/OFF button, the corresponding loading power levels to be changed 1-2-3-4.
Finally the letter P will appear to indicate that you have entered the grate cleaning stage,
where also here it is possible to change the cleaning intervals.
To exit programming mode press the ON/OFF button, the new selected parameters will be
entered automatically and the time will re-appear on the clock.
This programming can be carried out while the stove is working so that it is possible to
monitor the effects of the changes immediately.
Table of values - FI 3 DUAL - FI 4
Red Light value of setting (for the FI 4 model, reduce values by 10%)
PELLET Acc. 480g.
PELLET 1a p. 480g.
PELLET 2a p. 780g.
PELLET 3a p. 1050g.
PELLET 4a p. 1550g.
PELLET 5a p. 2100g.
PELLET 6a Time 1,25"
Green Light value of setting
Exhauster Acc. 190V.
Exhauster 1a 190V.
Exhauster 2a 190V.
Exhauster 3a 190V.
Exhauster 4a 190V.
Hearth cleaning 20 Min.
N.B. It is possible to display and modify the pellet loading rate setting for programmed ig-
nition by simply pressing the + and - buttons on the display, with the stove switched off.
38
540g. 600g. 660g.
540g. 600g. 660g.
840g. 900g. 9600g.
1200g. 1350g. 1450g.
1700g. 1850g. 1950g.
2250g. 2300g. 2400g.
1,50" 1,75" 2,00"
200V. 210V. 220V.
200V. 210V. 220V.
200V. 210V. 220V.
200V. 210V. 220V.
200V. 210V. 220V.
25 Min. 30 Min. 35 Min.
MAINTENANCE
Warning! Before carrying any maintenance, disconnect the power supply and wait
for the stove to cool down completely.
ORDINARY MAINTENANCE:
Weekly, by the user
• When the stove is not ignited and cold, vacuum clean the
ashes from the hearth base.
• Check the hearth and clean the holes if necessary, making
sure that all the holes are open.
• Clean any ash residues from the hearth holder and the
combustion air pipe (placed under the removable deflec-
tor, lean inside hearth holder) and the ignition resistance.
• Weekly, take out the flame breaker plate situated in the up-
per part of the fireplace and remove any ash deposited.
• Open the heat exchanger by turning the two inspection air
vents and vacuum out any dust. Cleaning increases power
delivery and good functioning of the stove.
• Clean the combustion chamber and the glass with non-
abrasive products.

EXTRAORDINARY MAINTENANCE:

every 1000 kg of pellets, this must be done by a professional technician
• Constantly check the state of the discharge gas bellows.
720g.
Front cleaning:
720g.
1020g.
• Remove the perforated combustion hearth and the hearth
1550g.
holder.
2050g.
• Remove the screw that locks the brick formed plate and
2500g.
2,25"
extract the plate by pushing it upwards.
• Remove the other four screws and extract the panel giving access to the horizontal
230V.
tubes.
230V.
• Carefully vacuum clean the tube bands from dust deposited in the heat exchanger.
230V.
230V.
• Reassemble all parts in an inverse sequence, oiling all screws.
230V.
40 Min.
Rear cleaning:
• Open the door on the left side of the stove and clean internally all discharge ducts (man-
ifold, fan scroll, smoke evacuator blades).
FI 3 FI 4
DUAL -
UK
39