JVC DR-MX1SEF Instructions Manual page 91

Automatic Satellite Program Recording does not start.
The DBS receiver is not connected properly to this unit.
]Connect the DBS receiver to the [VIDEO/AUDIO INPUT L1]
connectors properly. (
On the front display panel, "– –:– –" appears.
Power failure occurred.
]Set date and time correctly. (
"PROGRAM FULL" appears on the TV screen during timer
programming.
32 programs have already been timer programmed.
]Clear unnecessary programs on the unit, then try timer
programming again. (
The disc space does not increase when recorded titles are
cleared.
The PC's data recorded on a DVD-RAM drive cannot be cleared
on this unit.
]Format the disc. (When the disc is soiled, wipe the disc with a
soft dry cloth before formatting.) (
Timer Recording (VHS Deck)
Timer programming cannot be made.
Date and time is not correct.
]Set date and time correctly. (
The timer is not engaged.
]Press VHS TIMER and confirm that the VHS timer indicator
lights up on the front panel display.
Timer recording is in progress.
]Timer programming can't be performed while a timer recording
is in progress. Wait until it finishes.
Timer programming recording does not start.
Date and time is not correct.
]Set date and time correctly. (
The timer is not engaged.
]Press VHS TIMER and confirm that the VHS timer indicator
lights up on the front panel display.
The VHS recording lamp on the unit won't stop blinking.
The timer is engaged but there's no cassette loaded.
]Load a cassette with the record safety tab intact.
The loaded cassette has had its record safety tab removed.
]Remove the cassette and cover the hole with adhesive tape, or
insert a cassette with the record safety tab intact.
The tape is automatically ejected, then the unit is shut off.
The end of the tape was reached during timer recording.
]The program may not have been recorded in its entirety.
Next time make sure you have enough time on the tape to
record the entire program.
The end of the tape was reached during Instant Timer
Recording.
]The program may not have been recorded in its entirety. Next
time make sure you have enough time on the tape to record the
entire program.
VCR Plus+ Timer Programming cannot be made.
Date and time set on the unit is not correct.
]Set date and time correctly. (
The channel position does not correspond to that in the
receiving area.
]Set the correct channel position for the receiving broadcast.
( pg. 23)
pg. 59)
pg. 22)
pg. 58)
pg. 11, 87)
pg. 22)
pg. 22)
pg. 22)
The VCR Plus+ system does not timer-record properly.
The unit's channel positions have been set incorrectly.
]Refer to "Changing VCR Plus+
reperform the procedure.
Other Problems
The image of the TV broadcast appears distorted on the TV
screen.
For RF/AV/S-video connection
]Press PROGRESSIVE SCAN for 3 or more seconds so that the
Video output indicator (
For component video connection
]Press PROGRESSIVE SCAN for 3 or more seconds so that the
Video output indicator (
Whistling or howling is heard from the TV during camcorder
recording.
The camcorder's microphone is too close to the TV.
]Position the camcorder so its microphone is away from the TV.
The TV's volume is too high.
]Turn the TV's volume down.
When scanning channels, some of them are skipped over.
Those channels have been designated to be skipped.
]If you need the skipped channels, restore them. (
The channel cannot be changed.
Recording or Live Memory recording* is in progress.
]Press 9 to pause the recording, change channels, then press 4
to resume recording.
* HDD and DVD deck only
Channel settings that were made manually seem to have
changed or disappeared.
After the manual settings were made, Auto Channel Set was
performed.
]Perform "Manual Clock Set" (
Even though Auto or Semiauto Clock Set has been performed,
the clock is incorrect.
The clock setting data received from the host channel is
incorrect.
]Select a different host channel during "Semiauto Clock Set"
( pg. 22), or perform "Manual Clock Set" (
Malfunction occurs and the unit cannot be power off.
]Reset the unit by disconnecting the AC power plug from the AC
outlet and connect again.
TROUBLESHOOTING
® Setting" ( pg. 86) and
) lights off on the front display panel.
) lights up on the front display panel.
pg. 23)
pg. 22).
pg. 22).
91
EN