Dv Dubbing (Hdd & Dvd Deck Only) - JVC DR-MX1SEF Instructions Manual

EDITING
74
EN
DV Dubbing (HDD & DVD Deck Only)
You can dub programs from a camcorder or DV equipment
connected to the unit with a DV cable. The unit's remote control
allows you the limited control of the connected camcorder or DV
equipment functions during dubbing.
NOTES:
Use the DV cable VC-VDV 204U for connection.
When you connect a PC to the DV IN connector, we do not assure
the normal operation of this unit.
Your unit
Camcorder
DV equipment
The following on-screen display for DV dubbing appears when
ON SCREEN is pressed while the channel has been set to "DV".
0:00
HDD
00:00:00. 00
FR360
12bit DV JVC
DV
A
A Remote control switch
To switch between the devices operable by the remote control
unit. The unit is operable when the remote icon (
displayed faces to the left, while the DV device is operable
when the remote icon is facing to the right.
B Auto capture button
Select to start or pause the dubbing. If ENTER is pressed when
the DV device is in the pause condition, preroll editing* where it
is possible to dub with a start time that is highly accurate will be
activated. When the DV device cannot be operated from the
unit (such as in camera mode), proceed with normal recording
( pg. 41, 44).
* Preroll editing refers to the playback after the DV tape is slightly
rewind. (For DV devices that do not support the –1 speed, the
rewinding time may be longer.)
C Sound monitor switch
For selecting the desired sound format for recording. It is not
selectable during dubbing.
To [DV IN]
DV cable
(VC-VDV 204U)
(not supplied)
DV connector
1:00 2:00
DV
GR-DV3500
00:00:00. 00 L – R
GR-DV3500 SOUND1
1 2
DV
B C
1
Connect a camcorder or DV equipment to the [DV IN] connector
on the unit's front panel.
2
Press VHS/HDD/DVD SELECT on the unit repeatedly or HDD
on the remote so that the HDD lamp lights up on the unit.
3
Press CH +/– to set the channel to "DV".
4
Press ON SCREEN.
The on-screen display for DV dubbing appears.
5
Press w e to select
the remote icon (facing to the right) for the DV equipment.
6
Press REC MODE repeatedly to set the recording mode.
7
Locate the point from where you want to start dubbing, then
stop or pause playback by pressing the following buttons on the
remote control: 4, 5, 3, 8, 9
To play back in slow speed (1/10 of the normal speed), press 9 to
pause playback, then press 3 or 5.
To play back frame-by-frame, press 9 to pause playback, then press
9 repeatedly. Each press of 9 advances a frame.
To change the playback direction, press 3 or 5.
8
Press w e to select
until the desired sound track appears on the TV screen.
AUDIO 1
: Select this to record the original stereo sound played
back on the connected DV equipment.
AUDIO 2
: Select this to record the dubbed stereo sound played
back on the connected DV equipment.
MIX
: Select this to record the sound of both "AUDIO 1" and
"AUDIO 2".
Note that this selection is not available when the source program is
recorded in 16BIT (48 kHz) mode.
9
Press w e to select
dubbing starts.
Playback on the external DV equipment and recording on the unit
should start simultaneously.
To pause dubbing, press w e to select
ENTER. Both the unit and the external DV equipment pause
dubbing. Pressing 9 on the unit also works the same way.
10
Press w e to select
press 8. The DV equipment stops.
11
Press w e to select
12
Press 8 twice on the remote control to stop dubbing.
Both the unit and the external DV equipment stop dubbing.
NOTES:
Dubbing copyright guarded programs is not possible.
Original DV information such as the recording date and time are not
recorded.
The superimposed indication during the operation or dubbing is not
recorded.
If the dubbing is paused while the channel is set to "DV", you cannot
switch channels.
When you dub from DV equipment other than a
camcorder
A Perform step 1 to 4.
B Locate the point from where you want to start dubbing, then
)
stop on the DV equipment.
If you pause the DV equipment in this step, a few second's still
picture will be recorded at the beginning of the recorded program.
C Set the input mode to "DV INPUT" on the DV equipment.
If you select an input mode other than "DV INPUT", unwanted
pictures may be recorded at the beginning of the recorded
program.
D Perform step 9 to 12.
To skip unwanted part of the source picture
Press ENTER to stop both equipment, then press w e to select
.
Locate the point where you want to restart dubbing by pressing 4,
5, or 3, then press 8.
Press w e to select
dubbing.
, then press ENTER to display
.
, then press ENTER repeatedly
, then press ENTER. The
, then press
, then press ENTER. Then
, then press ENTER.
, then press ENTER to restart