Safety Instructions - Renkforce Kim Master Operating Instructions Manual

G Operating Instructions
Night light "Kim" (Master)
Item no. 1005406
Intended use
The product is intended for operation in a wall socket (230 V/AC, 50 Hz) and is operated
as a night light.
The night light can either be used in continuous operation or it can be activated by an
integrated PIR motion detector (detects temperature changes in the detection range).
In addition, the product controls one or several battery-operated slave night lights
(item no. 1005407, to be ordered separately) via an integrated transmitter.
The safety instructions must be observed at all times!
Any use other than that described above could lead to damage to this product and
involves the risk of short circuits, fire, electric shock, etc. No part of the product may
be modified or converted!
This product complies with the applicable national and European requirements. All
names of companies and products are the trademarks of the respective owners. All
rights reserved.
Contents
• Night light "Kim" (Master)
• Operating instructions
Explanation of Symbols, Inscriptions
The lightning symbol inside a triangle is a warning to inform you of potential
risks of personal injury, such as electrical shock.
This symbol indicates specific risks associated with handling, function and
use.
The "arrow" symbol indicates special tips and operating information.
The product is intended only for installation and use in dry interiors; it must
not be exposed to moisture or dampness.
The product complies with the protection class II.
Observe the operating instructions!
Safety Instructions
T he warranty will be void in the event of damage caused by failure to ob-
serve these safety instructions! We do not assume any liability for any re-
sulting damage!
W e shall not accept liability for damage to property or personal injury
caused by incorrect handling or non-compliance with the safety instruc-
tions! The warranty will be void in such cases!
• Unauthorised conversion and/or modification of the product is not al-
lowed for safety and approval reasons (CE).
• The product is not a toy and it should be kept out of the reach of children.
Children do not realise the danger arising from the incorrect use of electri-
cal devices. Therefore, be especially careful when children are around.
• Plug the product into a correct mains socket of the public mains supply
only. Do not connect the product to an extension cord.
• Do not use this product in rooms that are under adverse environmen-
tal conditions where combustible gases, vapours or dust are or may be
present! There is a risk of explosion!
• The product is intended for use only in dry indoor locations. It may not get
wet or damp; otherwise there may be danger of electric shock!
Never touch the product with wet hands!
• Do not expose the product to extreme temperatures, direct intense sun-
light, strong vibrations, high humidity or strong mechanical stress.
• Handle the product with care; it may be damaged by impacts, blows, or
accidental falls, even from a low height.
• Never connect the product to the wall outlet immediately after the prod-
uct has been brought from a cold room into a warm one. Condensation
that forms might destroy the product. Furthermore, there is a danger of an
electric shock. Wait until the product reaches room temperature and the
condensation has evaporated. This may take several hours.
• If it can be assumed that safe operation is no longer possible, the device
must be turned off and precautions must be taken to ensure that it is
not used unintentionally. After this, arrange for an expert to check the
product.
Safe operation can no longer be assumed if:
- the product shows visible signs of damage
- the product does not work at all or works poorly (where there is flicker-
ing light, leaking smoke or a smell of burning, audible crackling noises,
or discolouration of the product or to adjacent surfaces)
- the product was stored under unfavourable conditions
- it was exposed to heavy loads during transport
• Do not leave packaging material carelessly lying around, since it could
become a dangerous plaything for children.
• If you have any questions that are not answered in this manual, please
contact our technical service or another specialist.
Controls
2
4 5
1
1 Mains plug
2 LED light (on the front)
3 PIR motion detector (on the front)
4 Sliding switch for operating mode ("ON", "OFF", "AUTO")
5 Sliding switch for transmission channel (1, 2, 3)
6 Sliding switch for luminous period (3 minutes or 8 minutes)
Features of the PIR Motion Detector
The PIR motion detector responds to temperature changes in the detection range,
e.g. if a person enters the detection area with a temperature different from that of the
background (for example, a wall).
The range for detecting a temperature change in the detection range depends on sev-
eral factors:
• The temperature difference between the moving object and the background (ambi-
ent)
• Size of the moving object
• The distance of the object from the motion detector
• Ambient temperature
Due to the operating principle applied, it is not possible to detect tempera-
ture changes through glass.
If the PIR motion detector is directed towards e.g. a door, window or a heat-
er, electric devices or the like, faulty activations may result.
3
6