Table of Contents
Advertisement
Available languages
Available languages
Operating instructions
LED Strip RGB, 5 m
Item no. 1227385
Intended use
The product is intended for decorative or effect lighting in indoor areas; it may be installed and
used only in dry, enclosed indoor rooms.
The product can be fastened on suitable objects, such as furniture, using the adhesive tape
located on the bottom side of the LED strip.
The lighting programmes and light colours can be selected and controlled via the IR remote
control enclosed. The activation of the LEDs on the LED strip takes place via a special control
unit, whose power is supplied by the provided wall plug transformer.
Always observe the safety instructions and all other information included in these operating
instructions.
Any use other than that described above could lead to damage to this product and involves the
risk of short circuits, fire, electric shock, etc.
This product complies with the applicable national and European requirements. All names of
companies and products are the trademarks of the respective owners. All rights reserved.
Package contents
• LED strip
• Control unit with integrated IR receiver
• IR remote control (incl. battery)
• Wall plug transformer
• Accessory set (2x screws for mounting the control unit, 3M tape,
4x connection cables, 8x plugs)
• Operating instructions
Up-to-date Operating Instructions
Download the latest operating instructions at www.conrad.com/downloads or
scan the QR code above. Follow the instructions on the website.
Explanation of symbols
A triangle containing a lightning symbol indicates a health hazard, e.g., electric
shock.
The symbol with the exclamation mark in the triangle is used to highlight important
information in these operating instructions. Always read this information carefully.
The arrow symbol indicates special information and advice on operation.
Safety instructions
Damages due to failure to follow these operating instructions will void the
warranty! We do not assume any liability for any resulting damage! We do not
assume any liability for material and personal damage caused by improper
use or non-compliance with the safety instructions. In such cases, the
warranty will be null and void.
a) General
• Unauthorised conversion and/or modification of the product is not allowed for
safety and approval reasons.
• The product is not a toy and does not belong in the hands of children! Children
do not realise the danger arising from the incorrect use of electrical devices. In
addition, the product contains small parts and batteries. Therefore, be especially
careful when children are around!
• Do not leave packaging material carelessly lying around, since it could become a
dangerous plaything for children.
• In commercial institutions, the accident prevention regulations of the Employer's
Liability Insurance Association for Electrical Systems and Operating Facilities are
to be observed!
• If you have any questions that are not answered in these operating instructions,
please contact our technical department or another specialist.
b) Installation, connection and operation
• This product must be installed and used only in dry conditions indoors. The
product must not get damp or wet, as the wall plug transformer can pose the risk
of a fatal electric shock!
• Do not use the product in rooms that are under adverse environmental conditions,
where combustible gases, vapours or dust are or may be present! There is a risk
of explosion!
• The product must not be exposed to extreme temperatures, strong vibrations or
heavy mechanical stress.
• The product is suitable for use only in moderate climates, not tropical climates.
• Caution, LED light: Do not look directly into the LED light! Do not look into the
beam directly or with optical instruments!
• The mains socket into which the wall plug transformer is plugged must be easily
accessible.
• Do not pull the wall plug transformer from the mains socket by pulling on the cable.
• If the wall plug transformer is damaged, do not use the product any longer.
Switch off the mains socket to which the wall plug transformer is connected (switch
off at the corresponding circuit breaker or remove the safety fuse, then switch
off the earth leakage circuit breaker). Unplug the wall plug transformer from the
mains socket.
Replace the defective wall plug transformer only with a wall plug transformer of
the same design (with the same output voltage, output current, round plug and
plug polarity).
• If it can be assumed that safe operation is no longer possible, the device
must be turned off and precautions must be taken to ensure that it is not used
unintentionally.
Safe operation can no longer be assumed if:
- the product shows visible signs of damage
- the product does not work at all or works poorly (where there is flickering light,
leaking smoke or a smell of burning, audible crackling noises, or discolouration
of the product or to adjacent surfaces)
- the product was stored for a longer period of time in unfavourable conditions
- it was exposed to heavy loads during transport
• For safety reasons, unplug the wall plug transformer from the mains socket before
cleaning the product or when the product is not to be used for a while (e.g., during
storage).
c) Battery instructions
• Batteries should be kept out of the reach of children.
• Do not leave batteries lying around in the open; there is a risk of them being
swallowed by children or pets. If they are swallowed, consult a doctor immediately.
• Leaking or damaged batteries can cause burns if they come into contact with the
skin. You should therefore wear suitable protective gloves.
• Liquids leaking from batteries are very chemically aggressive. Objects or surfaces
coming into contact with these liquids might be considerably damaged. Therefore,
store batteries in a suitable location.
• Batteries must not be short-circuited, opened or thrown into a fire. There is a risk
of explosion!
• Do not recharge normal, non-rechargeable batteries; there is a risk of explosion!
• Please pay attention to the correct polarity (plus/+ and minus/-) when inserting
the battery.
Installation and start-up
a) Mounting the control unit
Before you start the installation, keep in mind that the IR receiver of the control unit
must be placed so that a flawless reception of the control signals from the IR remote
control is possible.
A direct optical contact between the IR LED of the IR remote control and the IR
receiver is beneficial; however, it is not a prerequisite. The IR light (invisible to the
human eye) of the IR remote control is reflected by many surfaces.
Before you proceed to the permanent mounting of the control unit and the IR
receiver, check that they function properly.
• The control unit can be screwed tight via two eyes located on the sides of the housing.
Depending on the mounting site, you can also fasten the control unit using cable ties or a
double-sided adhesive tape such as the supplied 3M tape.
When you screw the control unit into place, make sure that no cable or pipes are
damaged when drilling and tightening the screws.
• Fasten the IR receiver of the control unit to a suitable place, e.g. by using a strip of adhesive
tape or a cable tie.
b) Installing the LED strip
• The LED strip can be mounted on suitable surfaces, such as furniture or similar objects, using
the adhesive tape located on the bottom side.
The LED strip must be mounted in such a way that it is not exposed to mechanical
stress. It may not be mounted in such a way that someone can step on it; that will
damage it.
• Carefully clean the surface onto which you want to mount the LED strip from dust, dirt and
grease before mounting; otherwise the adhesive tape will come off the surface.
• Remove part of the protective strip and stick the LED strip onto the mounting surface one
section at a time. However, do not use force when pressing down.
The LED strip can be cut at the marked points. The connection cables provided
can be used to restore the electrical connection between the individual LED strip
sections.
Advertisement
Table of Contents
