Table of Contents
Advertisement
Available languages
Available languages
G Operating instructions
LED Flex Strip with Music Control, RGB, 5 m
Item no. 1342099
Intended use
The product is intended for decorative or effect lighting in indoor areas; it may be installed
and used only in dry, enclosed indoor rooms.
The product can be fastened on suitable objects, such as furniture, using the adhesive tape
located on the bottom side of the LED strip.
The lighting programmes and light colours can be selected and controlled via the IR remote
control enclosed. The activation of the LEDs on the LED strip takes place via a special con-
trol unit, whose power is supplied by the provided wall plug transformer.
As a special feature, a microphone is integrated in the control unit. Using this microphone,
the colours of the LED strip can also be controlled by sounds (e.g. music).
Always observe the safety instructions and all other information included in these operating
instructions.
Any use other than that described above could lead to damage to this product and involves
the risk of short circuits, fire, electric shock, etc.
This product complies with the applicable national and European requirements. All names of
companies and products are the trademarks of the respective owners. All rights reserved.
Package contents
• LED strip
• Control unit with IR receiver and microphone
• IR remote control (incl. battery)
• Power adapter
• Accessory set (2x screws for mounting the control unit, 2 connection plugs, 4 connection
cables, 8 plug clips)
• Operating instructions
Explanation of symbols
A triangle containing a lightning symbol indicates a health hazard, e.g., electric
shock.
This symbol points to specific risks associated with handling, function or opera-
tion.
The "arrow" symbol points to special tips and operating information.
Safety instructions
D amage due to failure to follow these operating instructions will void the war-
ranty! We do not assume any liability for any resulting damage!
W e do not assume any liability for material and personal damage caused by
improper use or non-compliance with the safety instructions. In such cases, the
warranty will be null and void.
a) General
• Unauthorised conversion and/or modification of the product is not allowed for
safety and approval reasons (CE).
• The product is not a toy and does not belong in the hands of children! Children
do not realise the danger arising from the incorrect use of electrical devices.
In addition, the product contains small parts and batteries. Therefore, be espe-
cially careful when children are around!
• Do not leave packaging material carelessly lying around; it could become a
dangerous plaything for children.
• In commercial institutions, the accident prevention regulations of the Employ-
er's Liability Insurance Association for Electrical Systems and Operating Facili-
ties are to be observed!
• If you have any questions that are not answered in these operating instruc-
tions, please contact our technical department or another specialist.
b) Installation, connection and operation
• This product must be installed and used only in dry indoor conditions. The prod-
uct must not get damp or wet as the wall plug transformer can pose the risk of
a fatal electric shock!
• Do not use the product in rooms with adverse environmental conditions, where
combustible gases, vapours or dust are or may be present! There is a risk of
explosion!
• The product must not be exposed to extreme temperatures, strong vibrations or
heavy mechanical stress.
• The product is suitable for use only in moderate climates, not tropical climates.
• Caution, LED light: Do not look directly into the LED light! Do not look into the
beam directly or with optical instruments!
• The mains socket into which the power adapter is plugged must be easily ac-
cessible.
• Do not pull the wall plug transformer from the mains socket by pulling on the
cable.
• If the wall plug transformer is damaged, discontinue use of the product.
Switch off the mains socket to which the wall plug transformer is connected
(switch off at the corresponding circuit breaker or remove the safety fuse, then
switch off the earth leakage circuit breaker). Only then unplug the wall plug
transformer from the mains socket.
Replace the defective wall plug transformer with a wall plug transformer of the
same design (with the same output voltage, output current, round plug and plug
polarity) only.
• If it can be assumed that safe operation is no longer possible, the device must
be turned off and precautions must be taken to ensure that it is not used unin-
tentionally.
Safe operation can no longer be assumed if:
- the product shows visible signs of damage
- the product does not work at all or works poorly (where there is flickering
light, leaking smoke or a smell of burning, audible crackling noises, or discol-
ouration of the product or to adjacent surfaces)
- the product was stored for a longer period of time in unfavourable conditions
- it was exposed to heavy loads during transport
• For safety reasons, unplug the wall plug transformer from the mains socket
before cleaning the product or when the product is not to be used for a while
(e.g., during storage).
Battery instructions
• Batteries should be kept out of the reach of children.
• Do not leave batteries lying around in the open; there is a risk they may be swallowed by
children or pets. If they are swallowed, consult a doctor immediately.
• Leaking or damaged batteries can cause burns if they come into contact with the skin.
You should therefore wear suitable protective gloves.
• Liquids leaking from batteries are very chemically aggressive. Objects or surfaces com-
ing into contact with these liquids could be considerably damaged. Batteries must there-
fore be stored in a suitable location.
• Batteries must not be short-circuited, opened or thrown into a fire. There is a risk of explo-
sion!
• Do not recharge normal, non-rechargeable batteries; there is a risk of explosion!
• Make sure that the battery is inserted into the IR remote control according to the correct
polarity (pay attention to positive/+ and negative/-).
Installation and start-up
a) Mounting the control unit
Before you start the installation, keep in mind that the IR receiver of the control
unit must be positioned in such a way that flawless reception of the control sig-
nals from the IR remote control is possible.
Direct optical contact between the IR LED of the IR remote control and the IR
receiver is beneficial; however, it is not a prerequisite. The IR light (invisible to the
human eye) of the IR remote control is reflected by many surfaces.
Before you proceed to the permanent mounting of the control unit and the IR
receiver, check that they function properly.
• The microphone is located behind the opening on the top of the control unit, and is used
in the corresponding operating mode to control the colours of the LED strip. The opening
must be aligned accordingly and depending on the volume of the sounds (music) used for
control.
The sensitivity of the microphone can be reduced if,for example., you put a piece of tape
over the opening.
• The control unit can be screwed down via two eyes located on the sides of the housing.
Depending on the mounting site, you can also fasten the control unit using cable ties or
double-sided adhesive tape.
When you screw the control unit into place, make sure that no cables or pipes are
damaged when drilling and tightening the screws.
• Fasten the IR receiver of the control unit to a suitable point, e.g. by using a strip of adhe-
sive tape or a cable tie.
Advertisement
Table of Contents
