Page 1
ISHING AND ONTOON NCHOR INCH PW24101 The 24’ Class anchor winch is a 12VDC power winch that retrieves and deploys river, mushroom, or navy type anchors using nylon rope. These anchor winches feature power-in and power-out operation with a switch that can be mounted on the helm.
ROPRIETARY TATEMENT The Powerwinch Anchor Winch is a product of Scott Fetzer Electrical Group or SFEG, located in Fairview, Tennessee, USA. The information contained in or disclosed in this document is considered to SFEG. Every effort has PROPRIETARY been made to ensure that the information presented in the document is accurate and complete.
24' C LASS NCHOR INCH OWERWINCH AFETY NFORMATION The following Safety Precautions Must be Followed at ALL Times. Failure to follow the warnings and cautions in this manual could result in serious injury and/or property damage. WARNING unplug the wiring harness before attempting LWAYS to install, relocate, service or perform maintenance on the winch.
24' C LASS NCHOR INCH OWERWINCH PECIFICATIONS Anchor Line Speed Motor Circuit Unit Dimensions Weight (No Load) Rope Voltage Breaker Weight (L x W x D) 40 lbs. 80 ft/sec 3/16" x 100' 12VDC 20 lbs. 10.5" x 6 x 9.25 (max.) Nylon EQUIRED...
24' C OWERWINCH LASS NCHOR INCH OUNTING THE 5/16" HOLE THROUGH Motor Wire Hole Mounting Template For 24' Anchor Winch For Technical Assistance: 303-469-3324 056014-001 Template 5" 5" Align End of Frame with Deck Edge 2" 5/16" HOLE THROUGH Winch Mounting Hole (4 plcs) Center of Roller 1 3/8"...
Page 6
24' C LASS NCHOR INCH OWERWINCH If not previously done, remove the 4 screws and cover and set aside. Place the mounting template on the deck in the desired location and secure with tape. 2.1. The winch may be mounted on the fore (front) or aft (rear) of the boat. 2.2.
24' C LASS NCHOR INCH OWERWINCH IRING THE WARNING disconnect the battery before working on LWAYS electrical equipment. WARNING use the recommended wire size and rated circuit LWAYS breakers. Failure to use the furnished and recommended sizes can cause a fire hazard and void warranty.
24' C LASS NCHOR INCH OWERWINCH 11. Push the switch through the switch mounting hole. Secure the switch with the switch boot. 12. At the battery, terminate the B wire with a 5/16 ring terminal. Connect LACK wire to the negative post of the battery. 13.
Check rope periodically for abrasion or deep cuts. Never splice an old rope with a new rope. If replacement is necessary, use only Powerwinch® rope specifically designed for this product. ROUBLESHOOTING...
24' C LASS NCHOR INCH OWERWINCH EPLACEMENT ARTS A N C H O R W IN C H C O N T R O L S W IT C H D O W N P O W E R W IN PW24501 Item Description Description...
OWERWINCH ARRANTY SFEG warrants to the retail Purchaser that the Powerwinch Product described in this FIRST manual is free of defects in material and workmanship within the terms and conditions as set forth below. SFEG’s obligation under this warranty is limited to the repair or replacement, at SFEG’s option, of any defective component within the stated warranty period.
Page 12
24' C LASS NCHOR INCH OWERWINCH ECORDS EALER NSTALLER DDRESS HONE URCHASE UMBER ERIAL UMBER RODUCT ESCRIPTION Retain your original proof of purchase. It is requi for all warranty repairs and returns. NOTES:...
Need help?
Do you have a question about the PW24101 and is the answer not in the manual?
Questions and answers