Table of Contents
Advertisement
Quick Links
............................................................................................................... 3
Features.............................................................................................................................. 3
Minimum Requirements .................................................................................................. 3
Package Content ............................................................................................................... 3
Note .................................................................................................................................... 3
Get to know the Broadband Router................................................................................ 4
Back Panel ......................................................................................................................... 4
Front Panel ........................................................................................................................ 5
Setup Diagram................................................................................................................... 6
Getting started................................................................................................................... 7
................................................................................................................... 15
Quick Setup ..................................................................................................................... 15
Step 1) Time Zone ........................................................................................................... 15
Step 2) Broadband Type................................................................................................. 16
1.1 Cable Modem ............................................................................................................ 18
1.2 Fixed-IP xDSL........................................................................................................... 19
1.3 PPPoE ........................................................................................................................ 20
1.4 PPTP .......................................................................................................................... 22
................................................................................................................... 25
General Settings .............................................................................................................. 25
2.1 System ........................................................................................................................ 27
2.1.1 Time Zone ............................................................................................................... 27
2.1.2 Password Settings .................................................................................................. 28
2.1.3 Remote Management............................................................................................. 29
2.2 WAN........................................................................................................................... 32
2.2.1 Dynamic IP ............................................................................................................. 33
2.2.2 Static IP Address.................................................................................................... 33
2.2.3 PPPoE (PPP over Ethernet).................................................................................. 33
2.2.4 PPTP ....................................................................................................................... 33
2.2.5 L2TP........................................................................................................................ 34
2.2.6 Telstra Big Pond..................................................................................................... 35
2.2.7 DNS ......................................................................................................................... 36
2.2.8 DDNS....................................................................................................................... 37
2.3 LAN ............................................................................................................................ 38
2.4 Wireless...................................................................................................................... 40
2.4.1 Basic Settings.......................................................................................................... 41
2.4.2 Advanced Settings.................................................................................................. 42
2.4.3 Encryption .............................................................................................................. 44
2.5 NAT ............................................................................................................................ 49
2.5.1 Port Forwarding .................................................................................................... 51
2.5.2 Virtual Server......................................................................................................... 53
2.5.3 Special Applications............................................................................................... 56
2.5.4 ALG Settings .......................................................................................................... 59
2.6 Firewall ...................................................................................................................... 60
1
Advertisement
Table of Contents
Related Manuals for Intellinet 521604
Summary of Contents for Intellinet 521604
-
Page 1: Table Of Contents
Introduction ... 3 Features... 3 Minimum Requirements ... 3 Package Content ... 3 Note ... 3 Get to know the Broadband Router... 4 Back Panel ... 4 Front Panel ... 5 Setup Diagram... 6 Getting started... 7 Chapter 1 ... 15 Quick Setup ... - Page 2 2.6.1 Access Control... 61 2.6.2 URL Blocking... 65 2.6.3 Hacker Prevention ... 67 2.6.4 DMZ ... 68 Chapter 3 ... 70 Status... 70 3.1 Status and Information ... 71 3.2 Internet Connection... 72 3.3 Device Status ... 73 3.4 Security Log... 74 3.5 Active DHCP Client Table ...
-
Page 3: Introduction
ADSL or cable modem. Simply configure your Internet connection settings in the Wireless Broadband Router and plug your PC to the LAN port and you're ready to share files and access the Internet. As your network grows, you can connect another hub or switch to the router’s LAN ports, allowing you to easily expand your network. -
Page 4: Get To Know The Broadband Router
The Reset button allows you to do one of two things. 1) If problems occur with your router, press the router’s reset button with a pencil tip (for less than 4 seconds) and the router will re-boot itself, keeping your original configurations. -
Page 5: Front Panel
Front Panel On the router’s front panel there are LED lights that inform you of the router’s current status. Below is an explanation of each LED and its description. Light Status WAN 10/100M WAN LNK/ACT Flashing LAN 10/100M (Port 1-4) -
Page 6: Setup Diagram
Setup Diagram Figure 1.2 below shows a typical setup for a Local Area Network (LAN). Figure 1.2... -
Page 7: Getting Started
Getting started This is a step-by-step instruction on how to start using the router and get connected to the Internet. 1) Setup your network as shown in the setup diagram above (fig 1.2). You then need to set your LAN PC clients so that it can obtain an IP address automatically. - Page 8 8: Reboot the PC. Your PC will now obtain an IP address automatically from your Broadband Router’s DHCP server. Note: Please make sure that the Broadband router’s DHCP server is the only DHCP server available on your LAN. Once you’ve configured your PC to obtain an IP address automatically, please proceed to...
- Page 9 5: Click OK to confirm the setting. Your PC will now obtain an IP address automatically from your Broadband Router’s DHCP server. Note: Please make sure that the Broadband router’s DHCP server is the only DHCP server available on your LAN.
- Page 10 6: Click OK to confirm the setting. Your PC will now obtain an IP address automatically from your Broadband Router’s DHCP server. Note: Please make sure that the Broadband router’s DHCP server is the only DHCP server available on your LAN.
- Page 11 7: Click OK to confirm the setting. Your PC will now obtain an IP address automatically from your Broadband Router’s DHCP server. Note: Please make sure that the Broadband router’s DHCP server is the only DHCP server available on your LAN.
- Page 12 DHCP servers off. (To disable the Broadband router’s DHCP server see chapter 2 LAN Port) 4) Once your PC has obtained an IP address from your router, enter the default IP address 192.168.2.1 (broadband router’s IP address) into your PC’s web browser and press <enter>...
- Page 13 The Status Information section is for you to monitor the router’s current status information only. Tools (Chapter 4) If you want to Reset the router (because of problems) or save your configurations or upgrade the firmware then the Tools section is the place to do this. Menu...
- Page 14 Backup (save), Restore, or Restore to Factory Default configuration for your Broadband router. The Firmware upgrade tool allows you to upgrade your Broadband router's firmware. The RESET tool allows you to reset your Broadband router. Selecting logout will return you to the LOGIN...
-
Page 15: Chapter 1
Once you click on the Quick Setup Wizard in the HOME page, you should see the screen below. Step 1) Time Zone The Time Zone allows your router to base its time on the settings configured here, this will affect functions such as Log entries and Firewall settings. -
Page 16: Step 2) Broadband Type
In this section you have to select one of four types of connections that you will be using to connect your broadband router’s WAN port to your ISP (see screen below). Note: Different ISP’s require different methods of connecting to the Internet, please check with your ISP as to the type of connection it requires. - Page 17 Menu 1.1 Cable Modem 1.2 Fixed-IP xDSL 1.3 PPPoE 1.4 PPTP Click on one of the WAN type and then proceed to the manual’s relevant sub-section (1.1, 1.2, 1.3 or 1.4). Click on Back to return to the previous screen. Description Your ISP will automatically give you an IP address Your ISP has given you an IP address already...
-
Page 18: Cable Modem
Click <OK> when you have finished the configuration above. Congratulations! You have completed the configuration for the Cable Modem connection. You can start using the router now, if you wish to use some of the advance features supported by this router see chapter 2, 3, 4. Description... -
Page 19: Fixed-Ip Xdsl
Click <OK> when you have finished the configuration above. Congratulations! You have completed the configuration for the Fixed-IP x DSL connection. You can start using the router now, if you wish to use some of the advance features supported by this router see chapter 2, 3, 4. Description This is the IP address that your ISP has given you. -
Page 20: Pppoe
1.3 PPPoE Select PPPoE if your ISP requires the PPPoE protocol to connect you to the Internet. Your ISP should provide all the information required in this section. Parameter User Name Password Service Name Description Enter the User Name provided by your ISP for the PPPoE connection Enter the Password provided by your ISP for the PPPoE connection... - Page 21 PPPoE connection. You can start using the router now, if you wish to use some of the advance features supported by this router see chapter 2, 3, 4. If you select “Continuous”, the router will always connect to the ISP.
-
Page 22: Pptp
1.4 PPTP Select PPTP if your ISP requires the PPTP protocol to connect you to the Internet. Your ISP should provide all the information required in this section. Parameter Obtain an IP address automatically Use the following IP address The ISP give you a static IP to be used to connect to the IP Address Description The ISP requires you to obtain an IP address by DHCP... - Page 23 WAN connection if the time period that no one is using the Internet exceeds the “Idle Time”. If you select “Manual”, the router will connect to ISP only when you click “Connect” manually from the Web user interface.
- Page 24 Click <OK> when you have finished the configuration above. Congratulations! You have completed the configuration for the PPTP connection. You can start using the router now, if you wish to use some of the advance features supported by this router see chapter 2, 3, 4.
-
Page 25: Chapter 2
If you have already configured the Quick Setup Wizard you do NOT need to configure anything thing in the General Setup screen for you to start using the Internet. The General Setup contain advanced features that allow you to configure the router to meet your network’s needs such as: Wireless, Address Mapping, Virtual Server, Access Control, Hacker Attack Prevention, Special Applications, DMZ and other functions. - Page 26 Below is a general description of what advance functions are available for this broadband router. Menu 2.1 System 2.2 WAN 2.3 LAN 2.4 Wireless 2.5 NAT 2.6 Firewall Select one of the above five General Setup selections and proceed to the manual’s relevant sub-...
-
Page 27: System
Select one of the above three system settings selections and proceed to the manual’s relevant sub-section 2.1.1 Time Zone The Time Zone allows your router to reference or base its time on the settings configured here, which will affect functions such as Log entries and Firewall settings. Description Select the time zone of the country you are currently in. -
Page 28: Password Settings
End Daylight Savings Time Click <Apply> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router (with the advance settings in place) 2.1.2 Password Settings You can change the password required to log into the broadband router's system web-based management. -
Page 29: Remote Management
2.1.3 Remote Management The remote management function allows you to designate a host in the Internet the ability to configure the Broadband router from a remote site. Enter the designated host IP Address in the Host IP Address field. Description Enter your current password for the remote management administrator to login to your Broadband router. - Page 30 Remote Management host IP address for this router (located in your company office), then you are able to configure this router from your home. If the Host Address is left 0.0.0.0 this means anyone can access the router’s web-based configuration from a remote location, providing they know the password.
- Page 31 Enabled Select “Enabled” to enable the remote management function. Click <Apply> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router (with the advance settings in place)
-
Page 32: Wan
Internet connection type. The WAN Settings screen allows you to specify the type of WAN port connect you want to establish with your ISP. The WAN settings offer the following selections for the router’s WAN port, Dynamic IP, PPPoE, PPTP, Static IP Address, DNS and DDNS. -
Page 33: Dynamic Ip
2.2.8 DDNS Once you have made a selection, click <More Configuration> at the bottom of the screen and proceed to the manual’s relevant sub-section 2.2.1 Dynamic IP Choose the Dynamic IP selection if your ISP will automatically give you an IP address. Some ISP’s may also require that you fill in additional information such as Host Name, Domain Name and MAC address (see chapter 1 “Cable Modem”... -
Page 34: L2Tp
2.2.5 L2TP Select L2TP if your ISP requires the L2TP protocol to connect you to the Internet. Your ISP should provide all the information required in this section. Parameter Obtain an IP address automatically Use the following IP address The ISP give you a static IP to be used to connect to the IP Address Subnet Mask Gateway... -
Page 35: Telstra Big Pond
Click <OK> when you have finished the configuration above. Congratulations! You have completed the configuration for the L2TPP connection. You can start using the router now, if you wish to use some of the advance features supported by this router see chapter 2, 3, 4. 2.2.6 Telstra Big Pond Select Telstra Big Pond if your ISP requires the Telstra Big Pond protocol to connect you to the Internet. -
Page 36: Dns
Click <OK> when you have finished the configuration above. Congratulations! You have completed the configuration for the Telstra Big Pond connection. You can start using the router now, if you wish to use some of the advance features supported by this router see chapter 2, 3, 4. 2.2.7 DNS A Domain Name System (DNS) server is like an index of IP addresses and Web addresses. -
Page 37: Ddns
Secondary DNS Address (optional) Click <Apply> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router (with the advance settings in place) 2.2.8 DDNS DDNS allows you to map the static domain name to a dynamic IP address. You must get an account, password and your static domain name from the DDNS service providers. -
Page 38: Lan
(with the advance settings in place) 2.3 LAN The LAN Port screen below allows you to specify a private IP address for your router’s LAN ports as well as a subnet mask for your LAN segment. - Page 39 255.255.255.0 802.1d Spanning Tree Disabled Description This is the router’s LAN port IP address (Your LAN clients default gateway IP address) Specify a Subnet Mask for your LAN segment If 802.1d Spanning Tree function is enabled, this router will use the spanning tree protocol to prevent from network loop happened in the LAN ports.
-
Page 40: Wireless
Domain Name Click <Apply> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router (with the advance settings in place) 2.4 Wireless Wireless Access Point builds a wireless LAN and can let all PCs equipped with IEEE 802.11b wireless network adaptor connect to your Intranet. -
Page 41: Basic Settings
(with the advance settings in place) 2.4.1 Basic Settings You can set parameters that are used for the wireless stations to connect to this router. The parameters include Alias Name, ESSID and Channel. -
Page 42: Advanced Settings
Channel Number Click <Apply> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router (with the advance settings in place) 2.4.2 Advanced Settings You can set advanced wireless LAN parameters of this router. The parameters include Authentication Type, Fragment Threshold, RTS Threshold, Beacon Interval, Preamble Type ……... - Page 43 WEP key in the "Encryption" page and wireless stations should use WEP encryption in the authentication phase to associate with this wireless router. If you select "Both", the wireless client can associate with this wireless router by using any one of these two authentication types.
-
Page 44: Encryption
2.4.3 Encryption By using Encryption, the data will be transmitted securely over the wireless network. You have to setup the same encryption key both on your router and wireless client devices. When the packet size is smaller the RTS threshold, the wireless router will not use the RTS/CTS mechanism to send this packet. - Page 45 You can generate the key by yourself and enter it. You also can enter a passphrase and let the router generate WEP key for you. In the 64-bit WEP mode, you can enter four WEP keys and select one of them as default key. Then the router can receive any packets...
- Page 47 Parameters Default Key Format Key Length Key 1 - Key 4 Description You may select to select ASCII Characters (alphanumeric format) or Hexadecimal Digits (in the "A-F", "a-f" and "0-9" range) to be the WEP Key. For example: ASCII Characters: guest Hexadecimal Digits: 12345abcde You may disable or enable the WEP function from the setting item.
- Page 48 Click <Apply> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router (with the advance settings in place) 64-bit WEP: input 10-digit Hex values (in the "A- F", "a-f"...
-
Page 49: Nat
Some applications require multiple connections, such as Internet games, video conferencing, Internet telephony and others. In this section you can configure the router to support these types of applications. You can select special applications that need “Application Layer Gateway” to support here. - Page 50 Click on one of the three NAT selections and proceed to the manual's relevant sub- section.
-
Page 51: Port Forwarding
The Port Forwarding allows you to re-direct a particular range of service port numbers (from the Internet/WAN Ports) to a particular LAN IP address. It help you to host some servers behind the router NAT firewall. Parameter Enable Port Forwarding... - Page 52 Click <Apply> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router (with the advance settings in place) Fill in the "Private IP", “Type”, “Port Range” and "Comment"...
-
Page 53: Virtual Server
2.5.2 Virtual Server Use the Virtual Server function when you want different servers/clients in your LAN to handle different service/Internet application type (e.g. Email, FTP, Web server etc.) from the Internet. Computers use numbers called port numbers to recognize a particular service/Internet application type. - Page 54 Click <Apply> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router (with the advance settings in place) Select the port number protocol type (TCP, UDP or both). If you are unsure, then leave it to the default both protocol.
- Page 55 Example: Virtual Server The diagram below demonstrates one of the ways you can use the Virtual Server function. Use the Virtual Server when you want the web server located in your private LAN to be accessible to Internet users. The configuration below means that any request coming form the Internet to access your web server will be translated to your LAN’s web server (192.168.2.2).
-
Page 56: Special Applications
2.5.3 Special Applications Some applications require multiple connections, such as Internet games, video conferencing, Internet telephony and others. In this section you can configure the router to support multiple connections for these types of applications. Parameters Enable Trigger Port Trigger Port... - Page 57 Click <Apply> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router (with the advance settings in place) Example: Special Applications If you need to run applications that require multiple connections, then specify the port (outbound) normally associated with that application in the "Trigger Port"...
- Page 58 2300-2400 and 47624 to be directed to that user. Note: Only one LAN client can use a particular special application at a time.
-
Page 59: Alg Settings
Enable Click <Apply> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router (with the advance settings in place) Description You can select to enable “Application Layer Gateway”, then the router will let that... -
Page 60: Firewall
2.6 Firewall The Broadband router provides extensive firewall protection by restricting connection parameters, thus limiting the risk of hacker attack, and defending against a wide array of common Internet attacks. However, for applications that require unrestricted access to the Internet, you can configure a specific client/server as a Demilitarized Zone (DMZ). -
Page 61: Access Control
2.6.1 Access Control If you want to restrict users from accessing certain Internet applications/services (e.g. Internet websites, email, FTP etc.), then this is the place to set that configuration. Access Control allows users to define the traffic type permitted in your LAN. You can control which PC client can have access to these services. - Page 62 Add PC Remove PC You can now configure other advance sections or start using the router (with the advance settings in place) Add PC Parameters Fill in “Client PC MAC Address” and “Comment” of the PC that is allowed to access the Internet, and then click “Add”.
- Page 63 Reset Click <Apply Changes> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router (with the advance settings in place) The description for this client PC rule.
- Page 64 Example: Access Control In the example below, LAN client A can only access websites that use Port 80. However, LAN client B is able to access websites and any other service that uses ports between 80 and 999.
-
Page 65: Url Blocking
2.6.2 URL Blocking You can block access to some Web sites from particular PCs by entering a full URL address or just keyword of the Web site. Parameters Enable URL Blocking Add URL Keyword Remove URL Keyword Description Enable/disable URL Blocking Fill in “URL/Keyword”... - Page 66 You can now configure other advance sections or start using the router (with the advance settings in place)
-
Page 67: Hacker Prevention
Click <Apply> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router (with the advance settings in place) If Internet attacks occur the router can log the events. -
Page 68: Dmz
2.6.4 DMZ If you have a local client PC that cannot run an Internet application (e.g. Games) properly from behind the NAT firewall, then you can open the client up to unrestricted two-way Internet access by defining a DMZ Host. The DMZ function allows you to re-direct all packets going to your WAN port IP address to a particular IP address in your LAN. - Page 69 You can now configure other advance sections or start using the router (with the advance settings in place) Note: You need to give your LAN PC clients a fixed/static IP address for DMZ to work properly.
-
Page 70: Chapter 3
Chapter 3 Status The Status section allows you to monitor the current status of your router. You can use the Status page to monitor: the connection status of the Broadband router's WAN/LAN interfaces, the current firmware and hardware version numbers, any illegal attempts to access your network, and information on all DHCP client PCs currently connected to your network. -
Page 71: Status And Information
3.1 Status and Information The Status and Information section allows you to view the router’s system information Parameters Information Description You can see the router’s system information such as the router’s: LAN MAC Address, WAN MAC Address, Hardware version, Serial Number, Boot code Version, Runtime code Version... -
Page 72: Internet Connection
3.2 Internet Connection View the Broadband router’s current Internet connection status and other related information Parameters Internet Connection Description This page displays whether the WAN port is connected to a Cable/DSL connection. It also displays the router’s WAN port: WAN IP address, Subnet Mask, and ISP Gateway as well as the Primary DNS and Secondary DNS being used. -
Page 73: Device Status
3.3 Device Status View the Broadband router’s current configuration settings. The Device Status displays the configuration settings you’ve configured in the Quick Setup Wizard/General Setup section. Parameters Device Status Description This page shows the Broadband router’s current device settings. This page displays the Broadband router LAN port’s current LAN IP Address and Subnet Mask. -
Page 74: Security Log
Parameters Security Log Description This page shows the current security log of the Broadband router. It displays any illegal attempts to access your network. At the bottom of the page, the security log can be saved <Save> to a local file for further processing or the security log can be cleared <Clear>... -
Page 75: Active Dhcp Client Table
3.5 Active DHCP Client Table View your LAN client's information that is currently linked to the Broadband router's DHCP server Parameters DHCP Client Log Description This page shows all DHCP clients (LAN PCs) currently connected to your network. The “Active DHCP Client Table”... -
Page 76: Statistics
3.6 Statistics View the statistics of packets sent and received on WAN, LAN and Wireless LAN. Parameters Statistics Description Shows the counters of packets sent and received on WAN, LAN and Wireless LAN. -
Page 77: Chapter 4
Description You can save the router’s current configuration, restore the router’s saved configuration files and restore the router’s factory default settings This page allows you to upgrade the router’s firmware You can reset the router’s system should any problem exist... -
Page 78: Configuration Tools
Saving the configuration settings provides an added protection and convenience should problems occur with the router and you have to reset to factory default. When you save the configuration setting (Backup) you can re-load the saved configuration into the router through the Restore selection. -
Page 79: Firmware Upgrade
Description This tool allows you to upgrade the Broadband router’s system firmware. To upgrade the firmware of your Broadband router, you need to download the firmware file to your local hard disk, and enter that file name and path in the appropriate field on this page. -
Page 80: Reset
4.3 Reset You can reset the router’s system should any problem exist. The reset function essentially Re-boots your router’s system Parameters Reset Description In the event that the system stops responding correctly or in some way stops functioning, you can perform a reset. Your settings will not be changed. -
Page 81: Appendix A
2) Type Ipconfig /all and <enter> • Your PC’s IP address is the one entitled IP address (192.168.1.77) • The router’s IP address is the one entitled Default Gateway (192.168.1.254) • Your PC’s MAC Address is the one entitled Physical Address (00-50-FC-FE-02-DB) -
Page 82: Glossary
(MAC) address information. Default Gateway (Router): Every non-router IP device needs to configure a default gateway’s IP address. When the device sends out an IP packet, if the destination is not on the same network, the device has to send the packet to its default gateway, which will then send it out towards the destination. - Page 83 NAT: Network Address Translation. This process allows all of the computers on your home network to use one IP address. Using the broadband router’s NAT capability, you can access the Internet from any computer on your home network without having to purchase more IP addresses from your ISP.
- Page 84 Subnet Mask: A subnet mask, which may be a part of the TCP/IP information provided by your ISP, is a set of four numbers (e.g. 255.255.255.0) configured like an IP address. It is used to create IP address numbers used only within a particular network (as opposed to valid IP address numbers recognized by the Internet, which must be assigned by InterNIC).
Need help?
Do you have a question about the 521604 and is the answer not in the manual?
Questions and answers