Page 1
AutoGet Wifi Intelligent Fiber Endface Microscope Please read this manual thoroughly before use. Properly keep this manual with the equipment for future reference.
Page 2
Introduction Dear customer: Thank you for choosing AutoGet Wifi product. This product has high quality and excellent perfor- mance. To make full use of this product, please read this manual carefully before using. Whenever you have any questions, please contact us and we are happy to support.
Page 3
AutoGetWifi Intelligent Fiber Endface Microscope Product Warranty Warranty Term We warrant that for a period of one (1) year from the shipping date, the product purchased by customer shall be free of defects in material and workmanship under normal authorized use. Warranty Content In the event that we receives notice during the warranty period that any part does not conform to its warranty, our sole and exclusive liability shall be, at its sole option, to either repair or replace...
Page 4
AutoGetWifi Intelligent Fiber Endface Microscope About the Manual Profile This chapter describes the name and function of each part. Hardware basic operation This chapter describes performance characteristics and the basic operation of the equipment. Software basic operation This chapter introduces software installation, features, interface and basic operation instructions.
AutoGetWifi Intelligent Fiber Endface Microscope 1 Profile 1.1 Check the packaging Referring the packing list of the products, please check whether all items are contained. If there are any missed items, please contact us immediately. 1.2 Product description Status Indicator Power Button Adapter Interface Touch Screen...
Page 8
AutoGetWifi Intelligent Fiber Endface Microscope Handle Angle Adjustment Button Touch Pen SD Card Slot Figure1-2 Touch pen: For touch screens. Handle angle adjustment button: SD card slot: Install SD card to store data and reports. USB Interface Battery status LED indicator Figure1-3 USB interface: DC 5V, Type C...
Page 9
AutoGetWifi Intelligent Fiber Endface Microscope Light-Sensor Touch Screen Focus Button Figure1-4 Light-Sensor: The screen brightness can be adjusted according to the ambient light intensity. Touch screen: Display image and software operation interface. Focus button: Manual focus button.
AutoGetWifi Intelligent Fiber Endface Microscope 2 Hardware basic operation 2.1 Features 1.Varies of adapters meet different requirements on inspect male fiber connectorfemale fiber connector, such as FC SC ST E2000 LCMU and TOSA ROSA fiber end-face. 2.AutoGetWiFihas high quality optical component and high resolution CCD sensor. 3.Support SD card storage.
AutoGetWifi Intelligent Fiber Endface Microscope 2.3 Hardware operation 2.3.1 Power On/Off To power on the device, press and hold the power button till the blue light indicator is on. Figure2-1 2.3.2 Remove the battery When the battery switch is in the position shown in the figure, the battery will automatically pop up, then gently push the battery and then pull it out.
AutoGetWifi Intelligent Fiber Endface Microscope Battery use precautions: 1.When in use, the battery shall be kept out from heat and high voltage. Avoid children’s touching. Do not drop or shock the battery. 2.Do not short the battery. Do not demolish or disassemble the battery. Do not put the battery in the damp place to avoid danger.
AutoGetWifi Intelligent Fiber Endface Microscope 2.3.6 Floodlight switch Light on Light off Figure2-6 Turn on the light switch to illuminate when the outside light is dark. 2.3.7 Replace the adapter Fasten the screw nut Figure2-7 Replace the adapter: 1.Loosen the lock nut of the adapter. 2.
AutoGetWifi Intelligent Fiber Endface Microscope 2.3.8 MT adapter use The rotation nut on the MT adapter marks the values 1, 2, and 3, and the mark values are aligned with the dots, respectively, and the measurement buttons are used for image acquisition. Figure2-8 NOTE: 1.
AutoGetWifi Intelligent Fiber Endface Microscope 3.2Device software interface 3.2.1 Device software main interface Power on the device, enter the software main interface. Figure3-1 Image display area: Display real-time images and measurement results. Image sharpness:The progress bar green indicates that the image is in a clear state. Setting: Software system settings and measurement task settings.
AutoGetWifi Intelligent Fiber Endface Microscope 3.2.2 Device software measurement task setting Click “Setting” on the interface to enter the measurement task setting interface as follows: Delete task Edit task Task Increase task Task name Task type Task zone name Task eaiting area Application settings Cancel to save and exit OK to save and exit...
AutoGetWifi Intelligent Fiber Endface Microscope 3.2.3 Device softwareSettings Click “Setting - Device” on the interface to enter the device setting interface as follows: Figure3-3 Image brightness: The user can adjust according to the actual image brightness, select the SF corresponding to adjust the image brightness under the SF measurement task, and select the MF corresponding to adjust the image brightness under the MF measurement task.
AutoGetWifi Intelligent Fiber Endface Microscope 3.2.4 Device software CCD Verification Click the interface "Settings - CCD" to enter the CCD Verification interface, the purpose is to eliminate the inherent dirty spots on the CCD. Figure3-4 3.2.5 About Click “Setting - About” on the interface to enter the about interface as follows: Figure3-5...
AutoGetWifi Intelligent Fiber Endface Microscope Note: It is necessary to restart the device after restoring factory settings. Check the software update: Before updating the software, you need to copy the installer to the SD card, click Update, and follow the prompts to upgrade. For details, see 3.1.1. Restore factory settings: Click Restore to restore the system settings, follow the prompts to restart.
Page 21
AutoGetWifi Intelligent Fiber Endface Microscope 1.Select a measurement task. Before selecting the MT measurement task, make sure that AF is ON and the Layer is ON. The following is an operation example under task IEC2.0-PC-MM-MT12. Figure3-7 2.Enter the MT12 measurement interface Figure3-8...
Page 22
AutoGetWifi Intelligent Fiber Endface Microscope 3.First image acquisition The MT interface rotation nut mark value 1 is aligned with the dot. The device measurement button is used to trigger image acquisition. If the acquisition fails or there are other abnormalities, please select the Redo or Cancel measurement button.
Page 23
AutoGetWifi Intelligent Fiber Endface Microscope 5. Third acquisition image The MT interface rotation nut mark value 3 is aligned with the dot. The device measurement button is used to trigger image acquisition. If the acquisition fails or there are other abnormalities, please select the Redo or Cancel measurement button.
Page 24
AutoGetWifi Intelligent Fiber Endface Microscope Measurement failures can be selected by selecting "Redo" or "Cancel ": 1. Unrecognized fiber Figure3-13 2. Failed to find the center Figure3-14...
Page 25
AutoGetWifi Intelligent Fiber Endface Microscope 3.Not detected all areas Figure3-15 Note: 1. When measuring multi-core MT, please perform image acquisition in strict accordance with the position of the rotating nut mark values 1, 2, and 3. If the image is not collected in the required order, the measurement will fail.
AutoGetWifi Intelligent Fiber Endface Microscope 3.3.3 Image brightness setting SF image brightness setting. If the brightness of the SF image is not suitable and you need to adjust it, follow the steps below: 1. Select SF task 2. Go to Settings - Devices, select SF, and then adjust the image brightness.
AutoGetWifi Intelligent Fiber Endface Microscope 3.3.4CCD Verification operation Verification method: 1.The adapter is connected to the clean ferrule of the end face. After clicking the “Verify” button, the prompt “1st image captured, please rotate the fiber and capture again”; 2. Click "OK", rotate the ferrule, and click the " Verify " button again, prompting "CCD Verifyfin- ished";...
AutoGetWifi Intelligent Fiber Endface Microscope 3.3.7 File view The storage file format is: data and report, saved in the device SD card. The file storage method is: 1. Not 2. Data 3. Report 4. Data and report 5. pass data and report 6.fail data and report 3.4 PC software interface 3.4.1 PC software main interface...
AutoGetWifi Intelligent Fiber Endface Microscope Image display area: Display measurement results. Task: Measurement tasks can be selected. Setting: Software system settings and measurement task settings. ID: ID numberwill be saved in data, report file INC□:The ID number is automatically increased after the measurement. Connect: Connect or disconnect wifi.
Page 31
AutoGetWifi Intelligent Fiber Endface Microscope Data and report setting interface: Figure3-23 Data and report storage path. SingleFiber data file name:Default name MeasureDataSF MultipleFiber data file name:Default name MeasureDataMF About interface: Figure3-24 Language selection: Support Chinese and English. Software version information: Displays the current software version number.
AutoGetWifi Intelligent Fiber Endface Microscope 3.4.3 PC software FTP function Click the “Ftp” button on the main interface of the PC software to open the SD card of the device directly. FTP usage: 1.PC connection device wifi name; 2. Click “Connect” on the main interface of PC software; 3.