Advertisement
Quick Links
Advertisement
Related Manuals for tayco Kip
Summary of Contents for tayco Kip
- Page 1 installation guide February 2020...
- Page 2 Installation Service toll free I 1.800.675.4092 Mon - Fri I 8:30 am – 5:00 pm EST www.tayco.com...
-
Page 3: Table Of Contents
Table of Contents General Instructions 1|03 Installation Checklist ........................ 1 Care and Maintenance ......................2 Application Guide ........................3 Kip Community Tables 04|19 Kip Community Table – 1 Surface ................... 04 Kip Community Table – 2 Surfaces ..................13... -
Page 4: Installation Checklist
2. Unpack products in the general order of installation (refer to Installation Sequence). WASTE MANAGEMENT 1. Establish a trash removal area separate from the product staging area. FEBRUARY 2020 kip 1... -
Page 5: Care And Maintenance
American Corporation. Painted Metals Tayco’s painted metal products are powder-paint-coated. To clean these products, use a damp cloth, using only a small amount of lukewarm water if necessary. Dry with a clean a dry cloth. To avoid scratching and damaging the painted surface, do not use hard bristled brushes or abrasive. -
Page 6: Application Guide
AND CONTAINS CONFIDENTIAL AND/OR PROPRIETARY INFORMATION. THE CONTENTS OF THIS DOCUMENT ARE NOT TO BE REPRODUCED, DISTRIBUTED, EXAMINED BY THIRD PARTY OR DIVULGED, IN WHOLE OR IN PART, WITHOUT THE WRITTEN AUTHORIZATION FROM TAYCO PANELINK LTD. `` DIMENSIONS ARE IN 11.25 13.5... -
Page 7: Kip Community Table - 1 Surface
Kip community table – 1 Surface 13. Place the surface face down on a clean solid surface or floor with the underside facing up, (Figure 1). 14. Position the bridge on the surface, (Figure 2). Continued on the next page >>... - Page 8 Kip community table – 1 Surface 15. Attach the combi dowels by screwing them into the pre- bored holes, (Figure 3). 16. Insert the wooden dowels, (Figure 4). Continued on the next page >> Figure 3 Figure 4 Tools & Hardware Needed...
- Page 9 Kip community table – 1 Surface 17. Insert the CamFix into the holes of the gables, (Figure 5). 18. Connect the gable to surface and press the boards together by inserting the combi dowels and wooden dowels into the holes of the gables, (Figure 6).
- Page 10 Kip community table – 1 Surface 21. Screw 1/4-20 X 35mm JCB bolts into the two holes at the corner of the bridge exposing an inch of the bolt, (Figure 8). 22. Set-in the topmost hole of the gable cover mount channel using one #10 X 1”...
- Page 11 Kip community table – 1 Surface 24. Align and flush the gable cover mount channel to the side face of the bridge before tightening the screws, (Figure 9). 25. Tighten the 1/4-20 X 35mm JCB bolts, (Figure 10). 26. Securely fasten the gable cover mount channel, using #10 X 1”...
- Page 12 Kip community table – 1 Surface 28. Securely fasten the bridge to the surface, using #10 X 1” Pan Head Screws, (Figure 11). 29. Securely fasten the bridge to gable, using #10 X 1” Pan Head Screws, (Figure 12). 30. Lift the table into an upright position;...
- Page 13 Kip community table – 1 Surface WARNING – To reduce the risk of fire, electric shock, or injury to persons: For indoor use only. Do not use with extension cords. Do not try to open the unit for any reason.
- Page 14 Kip community table – 1 Surface 36. Attach the gable cover brackets, using #10 X 11/16” Oval Head Screws into the pre- drilled holes of the gable cover, (Figure 14). Repeat this procedure for each gable cover required. 37. Angle the gable cover at 30 degrees;...
- Page 15 Kip community table – 1 Surface 38. Attach the bridge cover to bridge, using 1/4-20 X 35mm JCB bolts, (Figure 16). Figure 16 Tools & Hardware Needed 8540-1280 Drill Hex Bit 1/4-20 X 35MM JCB BOLT (8X) FEBRUARY 2020 kip 12...
-
Page 16: Kip Community Table - 2 Surfaces
Kip community table – 2 Surfaces 1. Place the surfaces on a clean solid surface or floor with the underside facing up; level the two surfaces and attach them together by inserting wooden dowels, (Figure 1). Continued on the next page >>... - Page 17 Kip community table – 2 Surfaces 2. Place the top bolt into the groove. Tighten the bolt using a box wrench, (Figure 2). 3. Attach the mending plates, using #10 X 1” Pan Head Screws, (Figure 2). 4. Position the bridge on the surface, (Figure 3).
- Page 18 Kip community table – 2 Surfaces 5. Attach the combi dowels by screwing them into the pre- bored holes, (Figure 4). 6. Insert the CamFix into the holes of the gables, (Figure 5). Continued on the next page >> Figure 4 Figure 5 Tools &...
- Page 19 Kip community table – 2 Surfaces 7. Connect the mid gable first to surface and press the boards together by inserting the combi dowels into the holes of the gable, (Figure 6). 8. Turn the CamFix on both sides of the mid gable to smoothly lock the gables and surface together, (Figure 7).
- Page 20 Kip community table – 2 Surfaces 10. Please refer to pages 6- 8. Follow Steps 6 - 14 to install the end gables, (Figure 8). Repeat this procedure to install the other end gable, (Figure 9). Continued on the next page >>...
- Page 21 Kip community table – 2 Surfaces 11. Securely fasten the bridges to surfaces, using #10 X 1” Pan Head Screws, (Figure 10). 12. Securely fasten the bridge to gable, using #10 X 1” Pan Head Screws, (Figure 11). 13. Lift the table into an upright position;...
- Page 22 Kip community table – 2 Surfaces WARNING – To reduce the risk of fire, electric shock, or injury to persons: For indoor use only. Do not use with extension cords. Do not try to open the unit for any reason.
- Page 25 0220...