Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for tayco One-Touch
Summary of Contents for tayco One-Touch
- Page 1 One-Touch installation guide March 2017...
-
Page 3: Table Of Contents
table of contents General Instructions installation checklist ................................1 care and maintenance ................................ 2 Mobile Training Desk 3/16 mobile training desk assembly ............................3 shelf assembly ..................................9 ganging mechanism removal............................. 11 ganging mechanism for back to back connection......................12 ganging mechanism for "L" connection..........................13 ganging mechanism for straight onnection........................14 wire trough and power/data attachment to metal modesty....................15 worksurface BYRNE grommmet installation........................16... -
Page 4: General Instructions
/DEHOHG IXUQLWXUH SODQV IRU LQVWDOODWLRQ SXUSRVHV DUH ORFDWHG LQ WKH KDUGZDUH ER[ (QVXUH WKDW GUDZLQJV DUH FRPSOHWH DQG KDQG\ EHIRUH EHJLQQLQJ LQVWDOODWLRQ :DVWH 0DQDJHPHQW (VWDEOLVK D WUDVK UHPRYDO DUHD VHSDUDWH IURP WKH SURGXFW VWDJLQJ DUHD JUNE 2011 one-touch table 1... -
Page 5: Care And Maintenance
VPDOO DPRXQW RI OXNHZDUP ZDWHU LI QHFHVVDU\ 'U\ ZLWK D FOHDQ GU\ FORWK 7R DYRLG VFUDWFKLQJ DQG GDPDJLQJ WKH SDLQWHG VXUIDFH GR QRW XVH KDUG EULVWOHG EUXVKHV RU DEUDVLYHV 7+( 86( 2) +$56+ &/($1(56 $1' &+(0,&$/6 0$< 3(50$1(17/< $/7(5 7+( 352'8&7 ),1,6+ $33($5$1&( $1' :,// 92,' $1< :$55$17< JUNE 2011 one-touch table 2... -
Page 6: Mobile Training Desk
FIGURE 1 Place the One-Touch mechanism on a clean, flat, smooth surface (Figure 1). Attach the leg to the mechanism with two 5/32 x 1-1/2 inches flathead hex machine screw and two 5/32 x 2 inches socket cap using the hex bit (Figure 2). - Page 7 FIGURE 3 Repeat step 2 to fasten the leg (Figure 3). Insert the screw-in button into the One-Touch mechanism. Turn the screw-in button clockwise until tightened (Figure 4). Repeat step 4 to install the screw-in button on the other side.
- Page 8 - cont'd. FIGURE 5 Push and hold the screw-in button to lift the legs up (Figure 5). Place the button caps on (Figure 6). PUSH and HOLD FIGURE 6 JUNE 2011 one-touch table 5...
- Page 9 - cont'd. FIGURE 7 Install the assembled One-Touch mechanism to the worksurface with 1-inch oval head screws using #2 Robertson bit on the pre-drilled positioning holes (Figure 7). Install the laminate (or metal modesty) to the specified...
- Page 10 1/2-inch using the Hex bit, (Figure 9), 10. Install the mechanism support at the middle of the mechanism using two 1-inch oval head screws with #2 Robertson bit (Figure 10). FIGURE 10 JUNE 2011 one-touch table 7...
- Page 11 6" hex bit 4, 5/32" round 4, 5/32" flathead 4, 5/32" socket 8, 1" oval head head hexmachine hex machine cap hex machine screw screw 1/2" screw 1 1/2" screw 2" JUNE 2011 one-touch table 8...
-
Page 12: Shelf Assembly
(Figure 4). FIGURE 2 FIGURE 3 NOTES: FIGURE 4 > The middle shelf bracket is not required for 42-inch width worksurfaces. > The middle shelf bracket is a pass-trough bracket. JUNE 2011 one-touch table 9... - Page 13 (in between the arms of the mechanism) while providing a small allowance between the shelf and the One-Touch mechanism. Secure the ends of the shelf assembly first with 1-inch oval head screws with #2 Robertson bit and then secure the middle shelf bracket along the mid-line of the worksurface (Figure 5).
-
Page 14: Ganging Mechanism Removal
1. Inspect where the ganging mechanisms are located; the standard location is on the ends. 2. Remove the screw on the ganging mechanisms using a #2 Robertson bit. tools and hardware needed drill #2 Robertson bit JUNE 2011 one-touch table 11... -
Page 15: Ganging Mechanism For Back To Back Connection
(Figure 2). FIGURE 1 FIGURE 2 user edge tools and hardware needed 14, #10; 11/16" ovalhead screw drill #2 Robertson bit user edge JUNE 2011 one-touch table 12... -
Page 16: Ganging Mechanism For "L" Connection
(Figure 2). FIGURE 1 FIGURE 2 tools and hardware needed NOTES: > To gang two worksurfaces; 14, #10; 11/16" both must have the same ovalhead screw drill #2 Robertson bit width. user edge JUNE 2011 one-touch table 13... -
Page 17: Ganging Mechanism For Straight Onnection
(Figure 2). FIGURE 1 FIGURE 2 user edge user edge tools and hardware needed 14, #10; 11/16" ovalhead screw drill #2 Robertson bit JUNE 2011 one-touch table 14... -
Page 18: Wire Trough And Power/Data Attachment To Metal Modesty
5/8-inch metal screws (Figure 2). FIGURE 2 #6x5/8" SHEET METAL SCREW #6x3/8" SHEET METAL SCREW tools & hardware needed #2 Robertson 2, #6; 5/8" sheet 4, #6; 3/8"sheet metal screw metal screw drill long bit JUNE 2011 one-touch table 15... -
Page 19: Worksurface Byrne Grommmet Installation
FIGURE 1 Mount the worksurface BYRNE grommet to the indicated hole on the worksurface (Figure 1). Run the power cord inside the modesty and plug the power cord to the power bar (Figure 2). FIGURE 2 JUNE 2011 one-touch table 16... - Page 20 0317 SCENE 2 MARCH 2017...
Need help?
Do you have a question about the One-Touch and is the answer not in the manual?
Questions and answers