Vivreau V3-204 Service Manual
Hide thumbs Also See for V3-204:

Advertisement

Quick Links

Service Manual
V3-204 and 205 Dispensing Systems
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the V3-204 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Vivreau V3-204

  • Page 1 Service Manual V3-204 and 205 Dispensing Systems...
  • Page 2: Table Of Contents

    Contact Vivreau if you have any questions ALL WIRING AND PLUMBING WARNING regarding the information contained in this MUST CONFORM TO NATIONAL AND LOCAL CODES.
  • Page 3: Important

    Model V3-204 is a Water Dispensing System designed This manual is solely for the use of qualified servicing of the Vivreau V3-204 and V3-205 Performance is the same for both models and for countertop installation with the CO Cylinder, CO installers and service technicians.
  • Page 4: Installation

    Below are the services required to be in place — ü " prior to the installation of the Vivreau V3-204 or V3- 205 Dispensing System. If you have any questions NA = Not Available regarding these or other services, please contact Vivreau Service Toll-Free at 877-999-1044.
  • Page 5 INSTALLER’S CHECKLIST 60 Hz (8 Amps) Vivreau Model V3-204 is designed to be installed with a minimum 1” clearance on the left and right sides. Below are the services required to be in place...
  • Page 6 V3-205, making sure Dispensers are tight and Remove the Overflow Plug, located on the Rear Panel on Installation Kit. Tighten all connections. straight. Regulator Model V3-204 and Front Panel on Model V3-205. In the event of a CO leak, close the Cylinder Valve, V3-204 V3-205 Prop the side opposite the Overflow Plug up about 1”.
  • Page 7: Operating Instructions

    After sanitizing, unplug unit. Remove Back and Bottle at a time. Service Panel, and install the normal service Filter Place appropriate container on Drip Tray beneath Vivreau Bottles should be filled to the line in the Cartridge. Dispensing Head. neck just below the Cap.
  • Page 8: Maintenance

    CALL SERVICE: If there is a problem, a Red LED will correctly. maintenance personnel. illuminate and the unit will beep. Please contact Vivreau Tighten the Nut firmly using a wrench. Service Toll-Free at 877-999-1044 immediately. EMPTY DRIP TRAY (Not Activated on this unit): Open the Valve on top of the Cylinder.
  • Page 9 10 seconds to flush through the Nozzle. the Water Level. Preserving & Restoring DO NOT use any abrasive material on your Vivreau Special stainless steel polishing cleaners can V3-204 or V3-205 Dispensing System. preserve and restore the protective film.
  • Page 10 Plug in Power Cord. inspect the water system for leaks. 2 ml Make sure the Refrigeration System is operating The Vivreau Dispensing System is ready for use. properly. Check the Sparkling Water flow-rate. It should IMPORTANT ________________________ dispense one liter in 20 seconds.
  • Page 11 CLEANING THE COOLING SYSTEM Assembly up from Dispenser Body. V3-204 CONDENSER GRILLE The Vivreau V3-204 and V3-205 Dispensing Systems are equipped with removable Nozzles for The Cooling System Condenser Grille is located on ease of cleaning and sanitizing. the front of the unit.
  • Page 12: Troubleshooting

    Troubleshooting Insert spring in Dispenser Handle. Reassemble the Dispenser Press Dispenser Collar down firmly, reinsert screw Push in Plastic Insert and position with Screw. and release the spring pressure gently. The information provided in this section is intended IMPORTANT ________________________ to assist in the identification and correction of any Alignment of the dimple and hole illustrated by the irregularities and malfunctions which might occur...
  • Page 13 CHILLER/CARBONATOR SYSTEM (continued) Still Water is Slower Than Normal and/or Carbonator is Running Very Loud. Problem Possible Problem Possible Cause Action pressure too low Regulator set incorrectly Reset CO Regulator volume too Water warm Refer to ‘Water warm’ section Refer to Water warm section Air in Carbonator System not purged during Vent Carbonator for five (5) seconds...
  • Page 14 Open and Cylinder Unplug the is full. Confirm Chiller/Carbonator Confirm the leak is pressure readings and plug back in to coming from the on CO Regulator. power the system Vivreau System. OFF and back ON Repair leak. again. Problem resolved Problem resolved...
  • Page 15 Water Sparkling Water is Flat Is Dispensing Warm Flush the Sparkling Water: 1. Switch the Cleaning Mode Switch OFF . Is unit Is CO 2. Touch and Hold the plugged into a Plug in unit Problem resolved Cylinder empty? working outlet? (Blue Sparkling Button until only LED Illuminated) Power Light...
  • Page 16 Leak LED is ON. Drip Tray Light is ON. Is the Gasket Is CO between the Replace Gasket. Empty Internal or Cylinder Valve or Regulator and Tank Check CO Pressure Is the CO Cylinder Secondary Shutoff External Drip Tray in place? Switch and change empty? Valve closed?
  • Page 17: Illustrated Parts List

    Item - corresponds with numbers on illustrations Part Number Description Ordering Parts for part identification. Use this parts list to order parts for your Vivreau V3- Compressor Set THB1335YS LST 120V Description - specifies part name or description 204 and V3-205 Dispensing System. 1017463 Thermostat of the item.
  • Page 18 Mini Bottler Cassette Fan 1025665 .380 Whiteline Braided Bev Tube (300’ roll) Condenser 1040294 Reg Pri WM 160 W/6’ Hose Attchd 1029135 AGIT-MOTOR-V3-204-US 1040289 Swivel ELL 1/4 Barb x 1/4 FFL 1040270 Water Inlet Solenoid 1040281 Nylon Washer White 1/4...
  • Page 19: Wiring Diagrams

    Contact Info Wiring Diagrams Phone Number: Vivreau V3-204 and V3-205 Wiring Diagram and Plumbing Schematic +1 877 999 1044 Email: INDICATOR PANEL – NOT VISIBLE InfoUSA@vivreau.com ICEBANK COMPRESSOR CONDENSER AGITATOR THERMOSTAT PROBE InfoCanada@vivreau.com SWITCH Or visit vivreauwater.com EARTH BASEPLATE CARBONATOR...

This manual is also suitable for:

V3-205

Table of Contents