Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Vivreau ViTap-2
Summary of Contents for Vivreau ViTap-2
- Page 1 Service Manual Vi Tap Dispensing System...
-
Page 2: Table Of Contents
ALL WIRING AND PLUMBING WARNING Contact Vivreau if you have any questions MUST CONFORM TO NATIONAL AND LOCAL regarding the information contained in this CODES. FAILURE TO COMPLY COULD RESULT manual. -
Page 3: Important
This manual is solely for the use of personnel Vivreau Vi tap 2, Vi Tap 2H, Vi Tap 1, and Vi Tap trained in the operation of the ViVreau Vi Tap 1H Dispensing Systems. -
Page 4: Installation
19” 19” Below are the services required to be in place prior Cylinder (Customer supplied) - Size should be Height ü ü to the installation of the Vivreau ViTAP Dispensing selected based on available space. Depth 18.5” 14" 14” ü... - Page 5 This appliance must WARNING IMPORTANT ________________________ to the installation of the Vivreau ViTAP Dispensing 20 Amp Electrical Recepticle (NEMA 5-20R) electrically grounded. System. Please review and check all services 230V, 60 Hz (11 Amps) Installation must be performed by properly before beginning work.
- Page 6 A device called a Water Block (supplied by Level the unit. retighten connection(s) and retest. If leak persists, Vivreau), must be installed between the Water Vi Tap-2H and Vi Tap-1H report leak to Vivreau. Supply Shutoff Valve and the Water Inlet to the unit.
- Page 7 WATER SUPPLY BOILER CHECK VALVE VENT For units with optional Boiler, connect water line to The Check Valve Vent is the green pipe located on the Boiler Filter. the lower left of the unit. Wiring Connector Hose Adapter Water may exit this pipe; especially when the water supply to the unit is restricted during operation of Vent the Carbonator Boost Pump.
-
Page 8: Operating Instructions
As a safety feature, to dispense Hot Water, Touch Minimum Pressure: 50 PSI Before operating the Vivreau ViTAP Dispensing and Release either Red Button, then Press and All Vents must open to fresh air and be kept clean... - Page 9 CHANGING A CO CYLINDER SECURE CYLINDER FOR UNITS WITH ECO MODE OPTIONAL HOT WATER BOILER Move empty Cylinder to storage area and secure All Boilers incorporate an ECO Mode function. WARNING Wear protective gloves and safely. Operating Boiler for the First Time: safety glasses when changing CO Cylinders.
-
Page 10: Maintenance
Use hot water if the unit is equipped with a Boiler. Preserving & Restoring IMPORTANT ________________________ DO NOT use any abrasive material on your Vivreau Special stainless steel polishing cleaners can ViTAP Dispensing System. preserve and restore the protective film. - Page 11 Turn the water supply back ON. Place the Cleaning Switch in the OFF position. Regulator and adjust if necessary. If working on a Vivreau ViTAP Dispensing System WARNING Make sure Do Not Use sign is with a Boiler, turn the handle on the Filter Head to displayed throughout the entire sanitation BYPASS the Dispensing Head during sanitation.
- Page 12 Cleaning Nozzle and Cover Remove the DO NOT USE Sign and carefully The Vivreau ViTAP Water Dispenser is now ready Fill a small container with Sanitizing Solution. inspect the system’s plumbing and fittings to for use.
- Page 13 deposits. The frequency of de-scaling will depend Drain remaining water from the unit. Tip the unit if Once in Calibration Mode, the unit will heat continuously until the Calibration Switch is on the amount of minerals (hardness) in the water. needed.
-
Page 14: Troubleshooting
Troubleshooting CHILLER/CARBONATOR SYSTEM (continued) The information provided in this section is intended IMPORTANT ________________________ Problem Possible Problem Possible Cause Action to assist in the identification and correction of any Water warm Reduced ice weight Faulty Ice Bank Control Replace, taking care to not damage the irregularities and malfunctions which might occur Maintenance and repairs must only be carried or long time to form... - Page 15 BOILER The Ready LED is used by the Boiler to show status and indicate errors or problems within the system. Still Water is Slower Than Normal and/or Carbonator is Running Very Loud. Flashes Symptom power Water level below elements. Open Valve and Water Supply Valve Check for Proper fully Open?
- Page 16 Change Filter power the system OFF and back ON Investigate other Is water Water Supply again. restored? issues. Problem resolved Problem resolved Water Leak Confirm the leak is coming from the Vivreau System. Repair leak. Problem resolved...
- Page 17 Water Is Dispensing Warm Sparkling Water is Flat Flush the Sparkling Water: 1. Switch the Cleaning Mode Switch Off. Is Unit Is CO 2. Touch and Hold the plugged into a Cylinder empty? Sparkling Button until only working outlet? (Blue LED Illuminated) Power Light Gas is dispensed.
- Page 18 CO2 Leak LED is ON. Is the Gasket Is CO between the Cylinder Valve or Check CO Pressure Replace Gasket. Is the CO Cylinder Secondary Shutoff Regulator and Tank Switch and change empty? in place? Valve closed? if needed. Problem resolved Connect a new CO Cylinder.
- Page 19 No Hot Water Water Tastes Bad Make sure Boiler is Do both Does only Does only plugged into a Is Boiler Power Still and Sparkling Sparkling Water Hot Water working outlet. Light ON? Water have a bad have a bad have a bad Press Power Button taste?
-
Page 20: Wiring Diagrams
Wiring Diagrams WIRING AND PLUMBING SCHEMATICS ECOBOILER UC4L 2.4KW (1000740) POWER LED ISP HEADER LED2 1 2 3 4 LED1 VI-2H Still 1 2 3 4 Spark and 1 2 3 4 VI-1H Still Vi TAP and Hot PROCESSOR CONTROLLER 1 2 3 4 VI-H Hot only... - Page 21 HOW TO USE ILLUSTRATED PARTS LIST Ordering Parts Parts Listings Parts listings identify serviceable parts with the Use this parts list to order parts for your Vivreau following categories: ViTAP Dispensing System. ViTAP-2 Single Serve Dispenser Exploded View Item - corresponds with numbers on illustrations For your convenience, part numbers have been for part identification.
- Page 22 ViTAP-2H Single Serve Dispenser Parts List Item Part Number Description Qty. ViTAP-2H Single Serve Dispenser Exploded View Shut Off Valve Supplied by Client 1025653 Boiler Tube 1/2” MPTx3/4” NH 1025654 Boiler Tubing 1/2” MPTx3/4” NH 1025655 Everpure Water Block Reset 1046016 Brass Female Connector (Garden Hose) 3/8 X 3/4 - 11.5 NH 1046036...
- Page 23 Contact Info Phone Number: +1 877 999 1044 Email: InfoUSA@vivreau.com InfoCanada@vivreau.com Or visit vivreauwater.com...
Need help?
Do you have a question about the ViTap-2 and is the answer not in the manual?
Questions and answers