Maintenance; Protecting The Environment - Stanley STHR323 Manual

Hammer drilling
• For hammer drilling in masonry and concrete, set the operating
mode selector (4) to the position and the drilling mode selector
(3) to the position. When hammering, the tool should not
bounce and run smoothly. If necessary, increase the speed.
Hammering
• For hammering with spindle lock, and for light chiselling and
chipping, set the operating mode selector (4) to the
position and the drilling mode selector (3) to the
position.
• When changing from hammer drilling to chiselling, turn the
chisel to the desired position. If resistance is felt during mode
change, slightly turn the chisel to engage the spindle lock.
Switching on and off
• Select the required speed by turning the speed selector dial
(2).
• To switch the tool on, press the on/off switch (1).
• To switch the tool off, release the on/off switch.
Brush monitor (Fig E)
Your tool has a built in system that monitors the health of the
brushes.
• Green brush monitor indicator (17). The brushes are in good
condition.
• Red brush monitor indicator (18). The brushes are warn and
need replacing, return your tool to an authorised Black &
Decker Service Centre in order to to have the brushes
replaced.

MAINTENANCE

Your STANLEY corded/cordless appliance/tool has been designed
to operate over a long period of time with a minimum of
maintenance. To ensure satisfactory operations, the tool must be
maintained and cleaned regularly
WARNING: To reduce the risk of injury, turn unit off
and disconnect machine from power source before
installing and removing accessories, before
adjusting or changing set-ups or when making
repairs. Be sure the trigger switch is in the OFF
position. An accidental start-up can cause injury.
• This machine is not user-serviceable. If problems occur contact
an authorised repair agent.
• The tool will automatically switch off when the carbon brushes
are worn.
• WARNING! Before performing any maintenance on corded/
cordless power tools:
• Switch off and unplug the appliance/tool.
• Or switch off and remove the battery from the appliance/ tool if
the appliance/tool has a separate battery pack.
• Or run the battery down completely if it is integral and then
switch off.
• Unplug the charger before cleaning it. Your charger does not
require any maintenance apart from regular cleaning.
• Regularly clean the ventilation slots in your appliance/ tool/
charger using a soft brush or dry cloth.
(Original instructions)
• Regularly clean the motor housing using a damp cloth. Do not
use any abrasive or solvent-based cleaner.
• Regularly open the chuck and tap it to remove any dust from the
interior (when fitted).
Lubrication
Your power tool requires no additional lubrication.
Accessories and attachments used must be regularly
lubrication around the SDS Plus fitment.
Cleaning
WARNING! Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and
around the air vents. Wear approved eye protection and
approved dust mask when performing this procedure.
WARNING! Never use solvents or other harsh
chemicals for cleaning the nonmetallic parts of the tool.
These chemicals may weaken the material of the parts.
Use only mild soap and damp cloth to clean the tool.
Never let any liquid get inside the tool,cleaning of
gasoline or other chemicals, never immerse any part of
the tool into liquid.
ACCESSORIES
The performance of your tool depends on the accessory used.
STANLEY accessories are engineered to high quality standards
and designed to enhance the performance of your tool. By using
these accessories you will get the very best from your tool.
Various types of SDS Plus drill bits and chisels are available as an
option.
Consult your dealer for further information on the appropriate
accessories.

PROTECTING THE ENVIRONMENT

Separate collection. This product must not be disposed
of with normal household waste.
Should you find one day that your STANLEY product needs
replacement, or if it is of no further use to you, do not dispose of it
with household waste. Make this product available for separate
collection.
STANLEY provides a facility for the collection and
recycling of STANLEY products once they have
reached the end of their working life. To take
advantage of this service please return your product to any
authorised repair agent who will collect them on our behalf. You
can check the location of your nearest authorised repair agent
by contacting your local STANLEY office at the address
indicated in this manual. Alternatively, a list of authorised
STANLEY repair agents and full details of our after-sales
service and contacts are available on the Internet at:
www.2helpU.com.
ENGLISH
7