Related Manuals for BodyCraft SW-95.0203
Summary of Contents for BodyCraft SW-95.0203
- Page 1 Assembly and Operating Instructions max. 130 kg ~ 220 Min. Art. No. SW-95.0201 218/35 kg L 182 | W 144 | H 206 Art. No. SW-95.0203 SW950201.01.01 Multi-gym Galena...
- Page 2 Galena...
-
Page 3: Table Of Contents
Content GENERAL INFORMATION Technical Data Personal Safety Set-Up Place ASSEMBLY General Instructions Scope of Delivery 2.2.1 Multi-gym 2.2.2 Leg Press (Optional) Assembly: Multi-gym Assembly: Optional Leg Press STORAGE AND TRANSPORT General Instructions TROUBLESHOOTING, CARE AND MAINTENANCE General Instructions Faults and Fault Diagnosis Maintenance and Inspection Calendar DISPOSAL RECOMMENDED ACCESSORIES... - Page 4 Galena...
- Page 5 BodyCraft® weight stations, for example, offer a very wide range of exercise possibilities. This ranges from traditional strength training such as bench presses to rehabilitation exercises and workouts for complex sports such as golf, tennis or badminton.
- Page 6 ABOUT THIS MANUAL Please carefully read the entire manual before installation and first use. The manual will help you to quickly set up the system and explains how to safely use it. Make sure that all persons exercising with the equipment (especially children and persons with physical, sensory, mental or motor disabilities) are informed about this manual and its contents in advance.
-
Page 7: General Information
GENERAL INFORMATION Technical Data Weight and Dimensions Packaging dimensions (L x W x H) and article weight (gross, incl. packaging) approx.: Box 1: 202 cm x 51.7 cm x 14.6 cm 50.7 kg Box 2: 121.3 cm x 104.1 cm x 24.1 cm 84.9 kg Box 3: 188 cm x 18.1 cm x 12 cm... -
Page 8: Personal Safety
Personal Safety DANGER ⚠ Before you start using the equipment, you should consult your physician that this type of exercise is suitable for you from a health perspective. Particularly affected are persons who: have a hereditary disposition to high blood pressure or heart disease, are over the age of 45, smoke, have high cholesterol values, are overweight and/or have not exercised regularly in the past year. -
Page 9: Set-Up Place
Set-Up Place WARNING ⚠ Do not place the equipment in main corridors or escape routes. ⚠ CAUTION Choose a location in which to place the equipment such that there is enough free space/ clearance to the front, the rear and to the sides of the equipment. The training room should be well ventilated during training and not be exposed to any draughts. -
Page 10: Assembly
ASSEMBLY General Instructions ⚠ DANGER Do not leave any tools, packaging materials such as foils or small parts lying around, as otherwise there is a danger of suffocation for children. Keep children away from the equipment during assembly. ⚠ WARNING Pay attention to the instructions attached to the equipment in order to reduce the risk of injuries. -
Page 11: Multi-Gym
2.2.1 Multi-gym... - Page 12 Galena...
-
Page 14: Leg Press (Optional)
2.2.2 Leg Press (Optional) NOTICE Please note that the leg press is an optional addition to the Galena multi-gym. The leg press is not included in the scope of delivery of the multi-gym and must be purchased separately. Galena... -
Page 16: Assembly: Multi-Gym
Assembly: Multi-gym Before assembly, take a close look at the individual assembly steps shown and carry out the assembly in the order given. NOTICE First loosely screw all parts together and check that they fit properly. Tighten the screws using the tool only when you are instructed to do so. - Page 18 Step 2: Asembly of the Weight Stack Insert two bushings (64) into the base frame (1). Insert the guide rods (5) into the base frame (1). Slide on the shorter stack spacers (6) and rubber cushions (38) onto the guide rods (5). ࣑...
- Page 20 Step 3: Assembly of the Top Frame Insert two bushings (64) into the holes of the top frame (10). Place the top frame (10) onto the guide rods (5) and the center upright (4). Mount the top frame (10) to the center upright (4) with three bolts (84) and three washers (90). Mount the pec dec upright (2) and press upright (3) to the top frame (10) with two bolts (78), four washers (90) and two nuts (87) each.
- Page 22 Step 4: Assembly of the Pec Dec Station Mount the pec dec support (13) and the pec dec pulley bracket (12) to the pec dec upright (2) with two bolts (72), two washers (89) and two nuts (86). Attach two square end plugs (32) to the pec dec support (13). Slide the adj.
- Page 24 Step 5: Assembly of the Arm Press Station Mount the press arm support (19a) to the top frame (10) with one bolt (71), two washers (88) and one nut (85). Insert one plug (32) into the top frame (10) and two plugs (32) into the press arm support (19a). Mount the press arm (20) to the press arm support (19a) with the press axle (24a).
- Page 26 Step 6: Assembly of the Top Cable ࣑ ATTENTION The pulleys must be assembled simultaneously while passing the cable. Insert the hook end of the top cable (45a) into the pulley slot in the front of the top frame (10) and pass the cable (45a) over pulley T1 back to T2 on the press upright (3).
- Page 28 Step 7: Assembly of the Pec Dec Cable ࣑ ATTENTION The pulleys must be assembled simultaneously while passing the cable. Loosely attach the pulleys P2 and P4 and the pulley guide brackets (18) to the pec dec pulley bracket (12) with one bolt (82) and one nut (87) each. Insert one end of the pec dec cable (46a) into the right adj.
- Page 30 Step 8: Assembly of the Ab Cable NOTICE The pulleys must be assembled simultaneously while passing the cable. Do not use this cable if you purchased the optional leg press. In that case, the leg press cable is installed here instead. Refer to the instructions for the leg press assembly and cable routing instead.
- Page 32 Step 9: Assembly of the Lower Cable ࣑ ATTENTION The pulleys must be assembled simultaneously while passing the cable. Insert the ball end of the lower cable (48a) and pass the cable under the pulley (49) [L1]. Pass the cable (48a) under the pulley (49) [L2]. Pass the cable (48a) over the lower pulley (49) [L3] mounted in the double pulley bracket (27a).
- Page 34 Step 10: Assembly of the Pads and Accessories Attach one rectangular end plug (35) to the top of the chrome back adjuster (30a). Mount the smaller press back pad (51) to the chrome back adjuster (30a) with two bolts (75) and two washers (90).
- Page 36 Step 11: Adjustment of the Cables After assembly of the cables, the length of the cables might need adjustment. The cables should be tightened to the point just before the top plate lifts off the weight stack. If the top plate is not resting on the weight stack, you must add length.
-
Page 38: Assembly: Optional Leg Press
Assembly: Leg Press The leg press is an optional addition to the Galena multi-gym. The leg press is not included in the scope of delivery and must be purchased separately. The leg press can only be used with the Galena multi-gym. - Page 40 Step 2: Assembly of the Leg Press Cable NOTICE If the pulleys (49) were previously assembled, they might need to be removed first and re- assembled during cable routing. If previously installed, completely remove the ab cable (94a) by unscrewing the bolt (80) [fig.
-
Page 42: Storage And Transport
STORAGE AND TRANSPORT General Instructions ⚠ WARNING The storage location should be chosen so that improper use by third parties or children can be prevented. If your equipment does not have transportation wheels, the equipment must be disassembled before transportation. ࣑... -
Page 43: Troubleshooting, Care And Maintenance
TROUBLESHOOTING, CARE AND MAINTENANCE General Instructions ⚠ WARNING Do not make any improper changes to the equipment. CAUTION ⚠ Damaged or worn components may affect your safety and the life of the equipment. Therefore, immediately replace damaged or worn components. In such a case, contact the contract partner. -
Page 44: Maintenance And Inspection Calendar
Maintenance and Inspection Calendar To avoid damage from body sweat, the equipment must be cleaned with a damp towel (no solvents!) after each training session. The following routine tasks must be performed at the specified intervals: Part Weekly Monthly Quarterly Cables Screw connections Pulleys and cable routing... -
Page 45: Recommended Accessories
RECOMMENDED ACCESSORIES To make your training experience even more efficient and pleasant, we recommend that you add suiting accessories to your fitness equipment. For training equipment like smith machines, weight benches or racks this could for example be a floor mat, which makes your fitness equipment stand more securely and also protects the floor from sweat but it could be also additional weights, handles, foot straps for leg exercises or triceps ropes. -
Page 46: Ordering Spare Parts
The serial number of your equipment is unique. It's located on a white sticker. The exact position of this sticker is shown in the following illustration. Enter the serial number in the appropriate field. Serial number: Brand / Category: BodyCraft / multi gym Model Name: Galena Article Number: SW-95.0201 (multi gym) / SW.95-0203 (leg press) -
Page 47: Parts List: Multi-Gym
Parts List: Multi-gym Name Qty. Name Qty. BASE FRAME BUSHING OF HAND GRIP (pre- assembled) PEC DEC UPRIGHT DOUBLE PULLEY BRACKET PRESS UPRIGHT LAT BAR HOLDER CENTER UPRIGHT FLOATING PULLEY BLOCK GUIDE ROD ADJ PULLEY BLOCK SHORTER STACK SPACER CHROME BACK ADJUSTER LONGER STACK SPACER 60mm SQUARE END PLUG WEIGHT PLATE (150LBS) - Page 48 1-1/4" HAND GRIP(LONGER) 3/8" X 3/4" HEX THREADED BOLT 1" X 70mm HAND GRIP 5/8" NYLON NUT 1" X 200mm ROUND HAND GRIP 1/2" NYLON NUT 1-1/4" X 140mm ROUND 3/8" NYLON NUT HAND GRIP 5/8" WASHER LAT BAR HOLDER COVER 1/2"...
-
Page 49: Parts List: Leg Press
Parts List: Leg Press Name Qty. Name Qty. Knob Connect tube Pulley Main frame Hand grip Front stabilizer Non-slip pad Leg press support Leg press cable Sliding tube 1/2" x 3" hex head bolt Foot rest 3/8" x 3" hex head bolt Handle bar 3/8"... -
Page 50: Exploded Drawing: Multi-Gym
Exploded Drawing: Multi-gym Galena... -
Page 51: Exploded Drawing: Leg Press
Exploded Drawing: Leg Press... -
Page 52: Warranty
WARRANTY Training equipment from BodyCraft® is subject to strict quality control. However, if a fitness equipment purchased from us does not work perfectly, we take it very seriously and ask you to contact our customer service as indicated. We are happy to help you by phone via our service hotline. - Page 53 Warranty Conditions For the warranty to be valid, the following steps must be taken: Please contact our customer service by email or phone. If the product under warranty has to be sent in for repair, the seller bears costs. After expiry of the warranty, the buyer bears the costs of transport and insurance.
-
Page 54: Contact
CONTACT TECHNIK TEKNIK OG SERVICE TECHNIQUE & SERVICE �� �� �� +49 4621 4210-900 80 90 16 50 +33 (0) 172 770033 +49 4621 4210-945 +49 4621 4210-933 �� +49 4621 4210-698 �� �� info@fitshop.dk service-france@fitshop.fr �� technik@sport-tiedje.de �� �� Åbningstider kan findes på... - Page 55 LIVE FITNESS WEBSHOP AND SOCIAL MEDIA Sport-Tiedje is Europe’s largest specialist store www.sport-tiedje.co.uk for home fitness equipment with currently over www.sport-tiedje.de/blog 70 stores and one of the world’s most renowned online mail order companies for fitness equipment. Private customers order via the 25 www.facebook.com/SportTiedje web shops in the respective national language or have their desired equpiment assembled on...
- Page 56 Notes Galena...
- Page 57 Notes...
- Page 58 Notes Galena...
- Page 60 Galena...