EAST OAK TORCH EO-PH001 Owner's Manual

EAST OAK TORCH EO-PH001 Owner's Manual

Patio heater 50000 btu
Hide thumbs Also See for TORCH EO-PH001:

Advertisement

TORCH Firecove
Patio Heater 50000 BTU
Owner's Manual
MODEL:
EO-PH001
EO-PH22002
EO-PH22003
EO-PH22004

Advertisement

Table of Contents
loading

Summary of Contents for EAST OAK TORCH EO-PH001

  • Page 1 TORCH Firecove Patio Heater 50000 BTU Owner’s Manual MODEL: EO-PH001 EO-PH22002 EO-PH22003 EO-PH22004...
  • Page 3 eastoak.com Question? Comments? Reach out to us to get expert support! support@eastoak.com eastoak.com 1-833-EAST-OAK (USA) (1-833-327-8625) Follow eastoakliving on Claim 3-year warranty at eastoak.com/warranty EASTOAK.COM PATIO HEATER...
  • Page 4: Important Caution

    IMPORTANT CAUTION Please verify all parts and components present and check for any damaged pieces before assembly. If you have any damaged or missing parts, please contact customer service at support@eastoak.com. • Some parts may contain sharp edges and may cause injury or property damage.
  • Page 5: Safety Guide

    WARNING • Do not store or use any gasoline or other flammable vapors or liquids close to this appliance. All propane tanks not connected to the heater should be stored at a separate location. • Improper installation, alteration, service, or maintenance may cause property damage, injury, or death.
  • Page 6 SAFETY GUIDE • Do not attempt to use fire to check for gas leaks. • Max. supply pressure is 11 WC. • Recommended propane gas tank size is as follows – diameter: 12”, height: 18”, weight: 20 lbs. • You must use a propane tank that has a collar to protect the gas valve. •...
  • Page 7 • Do not operate on a boat or vehicle. This unit must be used on a flat surface and outdoors ONLY. • Always remove protective cover before operating (if applicable). • Check for leaks after not using the unit for long periods of time. •...
  • Page 8 SAFETY GUIDE • Be mindful to not block the flow of combustion and ventilated air. Proper ventilation allows for the appliance to burn effectively. • Make sure the ventilation openings are free of debris. • Visually checking burner flames, with pictorial representations. •...
  • Page 9: Care And Maintenance

    CARE AND MAINTENANCE • Before any maintenance, always disconnect the propane gas tank. • Ensure the heater is free from any debris or combustible materials. • Use a soft brush to clean any mild stains, loose dirt, or soil only after the heater has completely cooled down.
  • Page 10: Parts Diagram

    PARTS DIAGRAM 1-833-327-8625 SUPPORT@EASTOAK.COM...
  • Page 11: Parts List

    PARTS LIST M8 Flange Nut Bolt M8x16 (packed with part I) (2 pcs packed with part I) (X2) (X3) *spare part X1 M6 Flange Nut Stainless Steel Bolt (X4) (X6) *spare part X1 *spare part X1 Bolt M6x30 Reflector Spacer (X6) (X3) *spare part X1...
  • Page 12 PARTS LIST Washer Post Bolt (X9) (X4) *spare part X1 *spare part X1 Screw M6x8 Cap Nut (X12) (X12) *spare part X1 *spare part X1 Wing Nut Wrench (X3) (X1) *spare part X1 1-833-327-8625 SUPPORT@EASTOAK.COM...
  • Page 13 Anchoring Arm Bolt M6x10 (X3) (X6) *spare part X1 M6 Nut (X6) *spare part X1 Before assembly, check and confirm all parts are present. Compare parts present with the content lists, including all hardware. If any parts or hardware pieces are missing or damaged, please contact customer service at support@eastoak.com.
  • Page 14 ASSEMBLY INSTRUCTIONS Flip the base upside down with the hollow side facing up. Attach the wheel assembly (I) to base (H) using 2 M8 flange nuts (AA) and 2 M8x16 bolts (BB). Then, AA (X2) BB (X2) connect the arm (MM) to the base (H) with 6 M6 nuts (OO) and 6 M6x10 bolts (NN).
  • Page 15 Attach lower post (F) to support brackets (G) using 6 pcs bolts M6x30 (EE) and 6pcs M6 flange nuts (CC). Secure bolts tightly. CC (X6) EE (X6) Place the tank housing on top of the post and slide the tank housing down towards the base. EASTOAK.COM PATIO HEATER...
  • Page 16 Insert the regulator (J) from the top end of the upper post (E), then attach the burner assembly (C) to upper post (E) using the 4 bolts (DD). DD (X4) Secure bolts tightly. Insert the regulator (J) from the top end of the lower post (F).
  • Page 17 WARNING: Remove protective covers before assembly. Note: If needed, loosen each screw prior to further assembly. II (X12) JJ (X12) Re-tighten screws once all sections are aligned. Attach 6 pcs reflector panels (A) to center reflector (B) using 12 pcs Screws M6x10 (II) and 12 pcs cap nuts (JJ). Fully tighten all of the screws.
  • Page 18 Attach 3 pcs reflector spacers (FF) and 3 pcs washers (GG) to burner assembly (C) firstly. Tighten the reflector spacers. Slide 3 pcs washers (GG) over threaded end of spacer. FF (X3) GG (X9) Attach the reflector assembly to the top of reflector spacer (FF) using 3 pcs washers (GG) and 3 pcs wing nuts (KK).
  • Page 19 Turn the cylinder valve on the tank clockwise to close the propane tank. Attach the regulator (J) to the cylinder valve by turning the regulator coupling nut clockwise. Make sure it is fastened securely and tighten connections by hand only. PRESSURE RELIEFVALVE CYLINDERVALVE...
  • Page 20: Operation

    OPERATION • Before performing a leak test, ensure that there are no open flames or flammable items nearby. Only move forward with the leak test in an open, spacious, outdoor area. Connect the propane tank to the regulator and turn the valve to the “OFF” position. Clean all connections with mild soap and water.
  • Page 21: To Turn The Heater Off

    • When lit for the first time the heater may emit a slight odor and smoke. This is a normal and temporary condition. Emitter screen will become a bright red due to the heat. The color is more visible at night. Flame patterns should be a blue flame;...
  • Page 22: Troubleshooting

    TROUBLESHOOTING Problem Cause Solution The burner will not light. The burner injector is clogged. Clean the burner injector. There is low gas supply pressure.C all your gas supplier. The bur There is low gas pressure.C all your gas supplier. immediately after ignition. The ignition is delayed.
  • Page 23: Warranty And Service

    WARRANTY AND SERVICE GUARANTEED 3-YEAR WARRANTY Thank you for choosing East Oak. This product is covered by our company warranty for up to 3 years from its original purchase date. CLAIM WARRANTY If you’d like to claim your product’s warranty, register your new product on our website at www.eastoak.com/warranty.
  • Page 24 Torch Firecove Patio Heater Series 1-833-327-8625 SUPPORT@EASTOAK.COM...
  • Page 26 support@eastoak.com eastoak.com 1-833-EAST-OAK (USA)

This manual is also suitable for:

Torch eo-ph22002Torch eo-ph22003Torch eo-ph22004

Table of Contents