ADC HiGain H2TU-C-202 User Manual page 26

Provisioning
Table 6 lists the Config screen PairGain Options and describes their available settings. Selections in bold typeface
are the factory default settings.
Table 6. H2TU-C-202 List 1E Config Screen PairGain Options
PairGain Options Screen Code Settings
(a)
Line Power Feed PWRF
Remote Provisioning RTPV
Bipolar Violation BPVT
Transparency
See "Bipolar Violation
Transparency (BPVT)
Option" on page 20.
HDSL2 BER HBER
Threshold
See "HDSL2 BER
(HBER) Option" on
page 19 and "System
Alarm Output Pins"
on page 54.
DS1 BER DBER
Special Loopback SPLB
Mode
SmartJack Loopback LPBK
Minor Alarm ALM
Network AIS Signal NAIS
H2TU-R DS1 Frame CONV
Conversion
See "H2TU-R DS1
Frame Conversion
(CONV) Option" on
page 20.
18
Description
OFF Disables powering to the HDSL2 pair.
ON Keeps the HDSL2 line voltage at the nominal -185 Vdc.
ENA Enables remote provisioning.
DIS Disables remote provisioning.
ENA Enables BPVs and HDSL2 CRC errors at the DS1 input to be converted
into DS1 BPVs at the DS1 output at the distant end. This makes HiGain
HDSL2 transparent to BPVs.
DIS Disables BPV Transparency.
1E-6 System alarm relay contact closes and the Status LED flashes red when
the Block Error Rate exceeds 10
definition of Bit Error Rate.)
1E-7 System alarm relay contact closes and the Status LED flashes red when
BER exceeds 10
NONE Prevents generation of a system alarm due to BER.
ENA Enables the fixed 24-hour T1 BER threshold.
DIS Prevents the generation of a system alarm due to T1 BER.
GNLB Configures the HiGain HDSL2 system to respond to the generic inband
loopback codes.
A2LB Configures the HiGain HDSL2 system to respond to the inband loopback
codes of the Teltrend addressable repeater.
A3LB Configures the HiGain HDSL2 system to respond to the inband loopback
codes of the Wescom addressable repeater.
A4LB Configures the HiGain HDSL2 system to respond to the inband loopback
codes of the Wescom Mod 1 addressable repeater.
ENA Enables the HiGain HDSL2 system to recognize all inband SmartJack
loopback commands.
DIS Configures the HiGain HDSL2 system to ignore all inband SmartJack
loopback commands.
ENA Enables the generation of the output alarm on pins 22 and 30 when a
system alarm condition occurs.
DIS Disables the generation of the output alarm on pins 22 and 30 when a
system alarm condition occurs.
CI If ALMP is set to AIS, this option specifies which pattern is sent to the
network when a remote LOS or AIS occurs. When configured for CI, an
AIS-CI pattern is sent to the network. For priority resolution, see
on page 41.
AIS When configured for AIS, an AIS pattern is sent to the network.
OFF Framing determined by the DS1 frame formatting option.
ACON Auto (ACON) detection of framing and potential frame conversion at the
remote.
FCON Auto detection of framing and forced frame format conversion (FCON) at
the H2TU-R.
April 21, 2000
-6
. (Block Error Rate is based on the
-7
.
152-202-115-04, Revision 04
Figure 25
H2TU-C-202 List 1E