Clas Ohlson SR432 Quick Start Manual

Dynamo AM/FM Radio with torch
Please read the entire instruction manual before using the product and
save it for future reference. We apologise for any text or photographic
errors and any changes of technical data. If you have any questions
concerning technical problems please contact our Customer Service
Department.
1. Description
• Dynamo radio, shock and moisture resistant, with headphone
outlet and built-in torch.
• Rechargeable NiMH battery but can also be operated from
2 x AAA/R03 batteries.
Dynamo crank
Torch
DYNAMO - BATT
Control switch for dynamo
or battery operation
Battery cover
Tuner
Volume control and
ON/OFF switch
2. Listening to the radio
1. Set the DYNAMO – BATT control switch to BATT or DYNAMO
depending on power source.
2. Turn on the radio by turning the volume control knob anti-clockwise.
3. Select the AM or FM band using its control switch.
4. Select the desired station with the TUNING knob.
5. FM: Extend the telescopic antenna completely and adjust if needed,
AM: Built-in aerial (adjust radio position for best reception).
6. Adjust the volume with the knob.
7. Shut off the radio by turning the volume control to the OFF position.
Quiet listening via the headphones (not included)
The radio is equipped with a 3.5 mm headphone jack and can be
connected to headphones with an 8 Ohm impedance. When the
headphones are used the speaker is turned off.
GREAT BRITAIN For consumer contact, please visit www.clasohlson.co.uk
and click on customer service.
• Article number 38-2948 • Model SR432
Telescopic aerial
Torch AM/FM radio
switch
– On/Off
Adaptor connection
Headphone outlet
Carry strap anchor point
You can operate the radio using three different power sources:
• Two R03/AAA batteries
• The built in 2.4 V rechargeable battery (which is charged
by the dynamo)
• Adaptor (not included).
3. Battery operation
Insert 2 x LR03/AAA batteries (not included)
1. Remove the battery cover by pushing it in direction of the arrow
and insert 2 x LR03/AAA batteries (not included). Insert the
batteries according to the marking in the battery compartment.
2. Select BATT with the DYNAMO – BATT switch.
3. Select a desired radio station and adjust the volume.
N.B. Do not mix new/old batteries or different types of batteries.
Remove the batteries if the radio will not to be used for a longer
period of time (to avoid leaking batteries).
NOTE: The radio's dynamo does not charge the R03 batteries.
4. Dynamo operation with the built-in 2.4 V
rechargeable battery
1. The radio has a built-in dynamo which can charge the built-in
battery. The radio then works totally independent of the regular
batteries.
2. Turn the volume control to OFF.
3. Fold out the dynamo crank and crank it in either direction (the
amount of charge depends on the time and amount cranked), for
example 2 cranks/sec for 90 sec will charge the radio for 20 min
listening at med. volume (operating time depends on volume used).
4. Select DYNAMO with the DYNAMO – BATT switch.
5. It is also possible to charge the battery while listening to the radio.
6. Fold in the crank.
7. Select a desired radio station and adjust the volume.
5. Use with adaptor (not included)
1. Connect the adaptor to the outlet, it must be 4.5 V DC, 300 mA and
have a + centre pin.
2. The batteries are automatically disconnected when the adaptor is
used while the rechargeable battery is charged even while listening
to the radio.
3. Select a desired radio station and adjust the volume.
6. Torch
The radio has a in-built torch which is controlled by the TORCH switch
(ON–OFF).
7. Disposal
Sort and recycle products where possible, instead of dispos-
ing of them. All electronic products, batteries and packaging
material etc. should be sorted and processed according to
local environmental regulations.
8. Specifications
Frequency range MW 540 – 1600 kHz (medium wave)
FM 88 – 108 MHz
Batteries
2 x LR03/AAA 1.5 V and built-in 2.4 V
(rechargeable, Ni-MH)
Headphone impedance 8 Ohms
Speakers
Ø 40 mm
Aerial FM telescopic aerial
Built-in AM ferrite aerial
Size 150 x 66 x 47 mm
ENGLISH