Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Paton MINI
Summary of Contents for Paton MINI
- Page 2 - 2 - PATON ECO DC MMA...
-
Page 3: Table Of Contents
3.3. “Anti-Stick” function 4. Care and maintenance 5. Generator operation 6. Storage 7. Transportation 8. Technical data 9. Scope of supply 10. Trouble shooting 11. Safety rules 12. Source schematic wiring diagram 13. Warranty obligations - 3 - PATON ECO DC MMA... - Page 4 Maximum wire Used electrode Set current value each core of the length, m mains wire, sq. mm 1x 220/230V – MINI, ECO-160, ECO-200, ECO-250 Ø not more than 80 А 2 mm Ø3 mm not more than 120 А Ø4 mm not more than 160 А...
-
Page 5: General
CAUTION! The mains button on the back of the MINI and ECO-160/200/250 models is not a power button, therefore, when the unit is turned off, it does not de-energize all internal electronics completely. For this reason, be sure to disconnect the plug from the mains after completing welding work, for safety reasons. - Page 6 * IP33 housing prevents particles with a diameter of more than 2.5 mm from entering the product, and also provides protection from rain when water falling down vertically or at an angle of 60º to the vertical line does not interfere with the operation of the unit - 6 - PATON ECO DC MMA...
- Page 7 2 ... 9 KG 1х25 250A 3 ... 13 KG 1х35 1 ... 9 KG 1х25 up to 315A 2 ... 12 KG 1х35 3 ... 18 KG 1х50 Fig. 1. Control elements and indicators - 7 - PATON ECO DC MMA...
-
Page 8: Start-Up
Place the unit so that cooling air can enter and exit freely through the vents on the front and rear panels. Make sure that no metal dust (e.g. when sanding) is sucked into the unit directly by the cooling fan. - 8 - PATON ECO DC MMA... -
Page 9: Power Connection
(international marking standard); 2) by using a bolted terminal on the rear wall of the unit (a stricter grounding standard, used in the CIS countries). Caution! When the unit is connected to a mains voltage higher than 270V (for MINI, ECO- 160/200/250) or 450V (for ECO-315-400V), all manufacturer's warranty obligations become invalid! The manufacturer's warranty obligations also become invalid in case of an erroneous connection of the mains phase to the source ground. -
Page 10: Hot-Start" Function
What helps to achieve this: when the voltage on the arc drops below the minimum allowable for stable arcing, the welding current increases by 30% of the set one (Fig. 4). Fig. 3. “HOT-START” function - 10 - PATON ECO DC MMA... -
Page 11: Anti-Stick" Function
Caution! Blowing from a short distance can result in damage to the electronic components; if there is a lot of dust, clean the cooling system ducts manually. - 11 - PATON ECO DC MMA... -
Page 12: Generator Operation
Welding current at: 5 min / 45% LD 150 A 160 A 200 A 250 A 315 A 5 min / 100% LD 94 A 101 A 126 A 158 А 210 A - 12 - PATON ECO DC MMA... -
Page 13: Scope Of Supply
- 1 pc; 4. Shoulder strap - 1 pc; 5. User manual - 1 pc; 6. Branded corrugated box / case * PATON - 1 pc. * For MINI-C, ECO-160-C, ECO-200-C, ECO-250-C models - 13 - PATON ECO DC MMA... -
Page 14: Troubleshooting
165V (or set current, until the arc can be all phases are slumped to ~ ignited. Then use the electrode 315V for ECO-315-400V) according to the current value. Continued on page 53 - 14 - PATON ECO DC MMA... -
Page 15: Safety Rules
- use only suitable (highly inflammable) clothing. PERSONAL PROTECTIVE EQUIPMENT For personal protection, observe the following rules: - wear protective footwear that retains insulating properties, even in wet conditions; - protect hands with insulating gloves; - 15 - PATON ECO DC MMA... - Page 16 - if possible, do not install the welding unit directly on an electrically conductive floor or work table, use insulating gaskets. REGULAR USE PRECAUTIONS Check the unit at least once a week for external damage and the operation of the safety units. - 16 - PATON ECO DC MMA...
-
Page 17: Source Schematic Wiring Diagram
12. SOURCE WIRING SCHEMATIC DIAGRAM - 17 - PATON ECO DC MMA... - Page 18 - 18 - PATON ECO DC MMA...
-
Page 19: Warranty Obligations
13. WARRANTY OBLIGATIONS PATON INTERNATIONAL guarantees the correct operation of the power supply provided that the consumer observes the rules of operation, storage, and transportation. CAUTION! There is no free warranty service for mechanical damage to the welding unit! UNIT MODEL... - Page 20 - in the absence of correct or even any kind of entries in the data sheet by the seller when selling the unit, - the warranty period is extended for the period of warranty service of the unit in the service center. - 20 - PATON ECO DC MMA...