Related Manuals for Taurus TF-PC2101
Summary of Contents for Taurus TF-PC2101
- Page 1 ’ OWNER S MANUAL CHEST PRESS / SHOULDER PRESS CAUTION Please read all instructions in this manual before use the equipment and keep the manual well.
- Page 5 Equipment Schematic right arm frame left arm frame Door Frame back pad Weight stack tower frame Rear floor frame set pad Front floor frame...
-
Page 8: Assembly Step
Assembly step 1 Steps Description Specifications Frame Hexagon socket countersunk head screws M12*30 Flat washer Φ24*Φ13*2.5 Spring washer 033-1 Transverse connecting frame 34-2... - Page 9 Assembly step 2 Steps Description Specifications Weight stack tower frame 33-2 Rear floor frame Front floor frame socket cap screw M10*25 socket cap screw M10*80 spring washer Flat washer Φ20*Φ10.5*2...
- Page 10 Assembly step 3 Steps Description Specifications Weight stack tower frame 33-2 Rotary frame Connecting rod frame Short spindle Washer circlip for shaft d0=25 Head socket with hexagon screw M8*20...
- Page 11 Assembly step 4 Steps Description Specifications Left arm frame 36-2 Right arm frame 37-2 Balance weight Long spindle Washer Plastic washer circlip for shaft d0=25 Head socket with hexagon screw M8*20 socket cap screw M10*95 spring washer...
- Page 12 Assembly step 5 Steps Description Specifications Back cushion frame 35-2 Support frame Adjustment board Gas springs Spindle Seat Adjuster roller 70-1176 socket cap screw M10*25 socket cap screw M10*130 spring washer Flat washer Φ20*Φ10.5*2 big washer Φ34*Φ11*3...
- Page 13 Assembly step 6 Steps Description Specifications Seat cushion frame Small spindle socket cap screw M10*25 spring washer big washer Φ34*Φ11*3...
- Page 14 Assembly step 7 Steps Description Specifications Back cushion Seat cushion socket cap screw M8*30 spring washer Flat washer Φ16*Φ8.4*1.6...
- Page 15 Assembly step 8 Steps Description Specifications Frame Guide rod Guide rod fixing sleeve Bumper φ38*φ21*10 Bumper φ62*φ20*26 Guide rod upper cap Select Pin Set Hexagon Socket Set S with Cone M8*20 Split Washer d=20 Top weight 4.5KG 10lb weight stack plate 4.5KG...
- Page 16 Assembly step 9 Steps Description Specifications Frame Side Shield Connecting strip Hexagon Socket Set S with Cone M8*20 Cross recessed countersunk head screw ST4.2*13 Flat washer Φ10*Φ5.3*1...
- Page 17 CABLE ROUTING DIAGRAM Correct Wrong Cable Cable limiting post limiting post...
-
Page 18: Exploded View
Exploded View... - Page 19 Exploded List Description Specifications Frame Guide rod Guide rod fixing sleeve Pulley baffle Left Shield Right Shield Side Shield Rear middle Trim Front middle Trim Connecting strip Pulley set φ89*25.8 Pulley set φ114*32 Bumper φ38*φ21*10 Floor mat Bumper φ62*φ20*26 Guide rod upper cap Hook stop collar Single Side glue cushion 25*35*3...
- Page 21 Exploded List Description Specifications Weight stack tower frame 33-2 Transverse connecting frame 34-2 Back cushion frame 35-2 Left arm frame 36-2 Right arm frame 37-2 Rotary frame Adjustment frame Support frame Rear floor frame Seat cushion frame Front floor frame Connecting rod frame adjustment frame connector...
- Page 22 Exploded List Description Specifications Handle grip Rotary knob Aluminum end cover Aluminum ring Aluminum ring Plastic ring Top weight 4.5KG 10lb weight stack plate 4.5KG circlip for shaft d0=25 knuckle bearing knuckle bearing deep groove ball bearing 6305-2Z Seat Adjuster roller 70-1176 Hex socket head cap screw M5*5...
- Page 24 Weight stack label instructions 1 Wipe front surface of weight stack 2 Peel off back sheet adhesive side from label and make sure that the label remains attached to the application tape 3 Aline the center hole of label with the weight stack center hole 4 Line up the first label to hole on top plate 5 Make sure label is straight and slowly press into place...
- Page 25 Heavy weight stack Heavy weight stack...
Need help?
Do you have a question about the TF-PC2101 and is the answer not in the manual?
Questions and answers