Advertisement
Quick Links
GC24002 - 04-14 F-150 5.5' bed
GC24004 - 04-14 F-150 6.5' bed
GC24010 - 08-14 Super Duty 6.5' bed
GC24019 - 15-Current F-150 5.5' bed
GC24020 - 15-Current F-150 6.5' bed
GC24021 - 17-Current Super Duty 6.5' bed
THE GATOR EFX HARD FOLD TONNEAU COMES FULLY ASSEMBLED.
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT.
READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
DO NOT OVER TORQUE. A TORQUE WRENCH IS NOT NECESSARY.
IF PREFERRED, TORQUE IS APX 120 INCH LBS.
PN
1
Hard Folding Cover (1)
2
Driver (Left) Mounting Rail (1)
3
Passenger (Right) Mounting Rail (1)
4
Clamps (x6)
5
Cover Retainers (x4)
6
Bulkhead Seal (1)
7
Drain Tubes (x2)
Ratchet & 1/2" Socket
Page 2 of 8
Gator EFX Hard Fold
Tonneau Cover
GC34006 - 09-19 RAM 5.5' bed
GC34008 - 19-Current RAM 1500 Crew Cab 5.5' bed
GC34009 - 19-Current RAM Quad/Mega Cab 6.5' bed
PARTS LIST OF COMPONENTS
Part Description/ Qty
PN
Components
Tools Required
30-60 min
Cutting Not Required
customerservice@realtruck.com
855-427-4568
3-YEAR WARRANTY
GC-M5
Part Description/ Qty
Drilling Not Required
Advertisement
Related Manuals for Gator EFX Hard Fold
Summary of Contents for Gator EFX Hard Fold
- Page 1 GC24020 - 15-Current F-150 6.5' bed GC24021 - 17-Current Super Duty 6.5' bed 30-60 min Cutting Not Required Drilling Not Required THE GATOR EFX HARD FOLD TONNEAU COMES FULLY ASSEMBLED. customerservice@realtruck.com REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. 855-427-4568 3-YEAR WARRANTY READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
- Page 2 INSTALLATION PROCEDURE 1. Attach both left and right side rails to the truck bed. The end of the mounting rail with the drain tube tting will go towards the cab of the truck, position ush to bulkhead. 2. Position the top edge of mounting rail ush to 1/8” above the top edge of your truck bed rail. 3.
- Page 3 5. Set the tonneau onto the mounting rails, the buckles should be to the front. 6 & 7. Assemble the four retainer clamps, slide each of them into the track on the underside of the tonneau, slide into position, but do not tighten at this time. Page 4 of 8...
- Page 4 8. Carefully unfold the cover. Position the cover so it is centered side to side and front to back on the truck bed. 9. Test the rear latching assembly for smooth operation as this is the best indicator of the cover being posi- tioned correctly.
- Page 5 12 & 13. Once in the open position double check the clamp engagement to the side rail and tighten. Test the cover again for proper operation, adjust as needed, then tighten the star knobs. of the truck bed. This can be done by placing the tube behind a bed liner, through an existing hole in the bed, or by drilling a 5/8”...
- Page 6 OPERATION INSTRUCTIONS 1 & 2. To open the cover: Lower the tailgate and pull the cable. While pulling on the cable lift the panel up and towards the cab. 3, 4 & 5. Release the strap from the stowed position by squeezing the tabs. Attach the buckle at the bulk- head, pull the strap to take up the slack and secure the cover.
-
Page 7: Warranty Coverage
WARRANTY COVERAGE Terms of Warranty The structure of your cover is warranted to be structurally free from defects in material and workmanship for (3) three years from the retail date of purchase. The hinges, seals, and hardware are warranted to be free from defects in material and workmanship for (3) three years from the retail date of purchase.