Table of Contents
Advertisement
Note
• If you have not set the clock, the clock setting window will appear instead of the Timer Programming
list. Continue from step 4 in "Clock Setting" on page 22 before programming the timer.
• Press [Cursor { / B] to move the cursor in the Timer Programming list.
• If a basic recording or One-touch Timer Recording is in progress on one component (e.g. VCR) and
the timer recording set for the other component (e.g. DVD) is about to begin, the unit automatically
switches to the programmed channel for timer recording 2 minutes before the programmed starting
time, and the recording in progress (for VCR) will be cancelled UNLESS their recording channels are
the same. If their recording channels are the same, the timer recording will start without cancelling the
recording currently in progress. In this case, the recording of the same channel will be made on both
DVD and VCR.
• Cancel the timer-standby mode by pressing [T-SET] before operation for either DVD or VCR. When
finished operating, press [T-SET] to resume the timer-standby mode.
• In the timer-standby mode, you can turn on the power and use the component (VCR or DVD) which is
not currently timer-programmed.
Checking, cancelling, or correcting the timer
programming information
In the following example, No.
5 timer programming overlaps
on No. 1 and No. 6 timer
programmes. In such a case, you
should correct the programme
time to clear the overlap.
Timer Programming
Date
Start
End
1. 01/01 12:00
13:00 P01
2. - - -
3. - - -
No.1 6
4. - - -
5. 01/01 12:30
14:00 P02
6. 01/01 13:45
21:00 P12
7. - - -
8. - - -
1
Press [T-SET] so that the
icon disappears from the front
panel display.
2
Press [TIMER PROG. SHOWVIEW]
twice.
Timer Programming list will appear.
Timer Programming
Date
Start
End
1. 01/01 12:00
13:00 P01
2. - - -
3. - - -
4. - - -
5. - - -
6. - - -
7. - - -
8. - - -
32
EN
Downloaded from:
http://www.usersmanualguide.com/
Timer Recording (cont'd)
3
Check the information on the
list you will need.
4
To clear the timer program-
VCR
DVD
ming, select the desired pro-
DVD
VPS
CH
Mode
VCR
PDC
gramme using [Cursor K / L],
DVD
XP
ON
then press [CLEAR/C-RESET].
Overlap
To correct the timer program-
DVD
SP
ON
ming
DVD
SEP
ON
1) Select the desired programme
using [Cursor K / L], then
press [ENTER].
2) Correct the timer programming
using [Cursor K / L / { / B].
3) Press [ENTER] again.
5
Press [TIMER PROG. SHOWVIEW]
to exit.
6
Press [T-SET] to return to the
timer-standby mode.
VCR
DVD
DVD
VPS
CH
Mode
To check the timer program-
VCR
PDC
DVD
XP
ON
ming in process
Press [TIMER PROG. SHOWVIEW].
Recording
OPERATE
OPEN/CLOSE
SETUP
DUBBING
EJECT
TIMER PROG.
1
T-SET
SHOW VIEW
REC MODE
RAPID PLAY
VCR
DVD
ZOOM
CM SKIP
6
TOP MENU
MENU LIST
ENTER
RETURN
.@/:
ABC
DEF
1
2
3
GHI
JKL
MNO
6
4
5
PQRS
TUV
WXYZ
7
8
9
CLEAR/C-RESET
SPACE
DISPLAY
0
REV
FWD
PLAY
VCR
DVD
REC/OTR
REC/OTR
STOP
REPEAT
AUDIO
SEARCH
SLOW
PAUSE
Note
• If a timer recording is
proceeding, that programme
is highlighted in red. In such
a case, you cannot select any
other programmes.
• When you check the timer
programming in progress
by pressing [TIMER PROG.
SHOWVIEW] during
operations of the component
(VCR or DVD) which is not
currently used for the timer
recording, the programme
will not be highlighted. In this
case, you cannot select other
programmings.
2
5
6
PROG.
SKIP
4
Advertisement
Table of Contents
