Checking, Cancelling, Or Correcting The Timer Programming Information; To Stop The Timer Recording In Progress; If The Timer Programming Did Not Complete Correctly - Sharp DV-SR85S(S Operation Manual

Checking, cancelling, or correcting the timer
programming information
In the following example, No.
5 timer programming overlaps
on No. 1 and No. 6 timer
programmes. In such a case, you
should correct the programme
time to clear the overlap.
Timer Programming
Date Start End CH Mode
1. 01/01 12:00 13:00 P01 XP
2. - - -
3. - - - Overlap
No.1 6
4. - - -
5. 01/01 12:30 14:00 P02 SLP
6. 01/01 13:45 21:00 P12 SEP
7. - - -
8. - - -
1
Press [ OPERATE] so that the
icon disappears from the
front panel display.
2
Press [TIMER PROG. SHOWVIEW]
twice.
Timer Programming list will appear.
Timer Programming
Date Start End CH Mode
1. 01/01 12:00 13:00 P01 XP
2. - - -
3. - - -
4. - - -
5. - - -
6. - - -
7. - - -
8. - - -

To stop the timer recording in progress

Press [STOP C] on the front panel of the unit.

If the timer programming did not complete correctly

The error number appears on the
Timer Programming list.
Timer Programming
Date Start End CH Mode
* 01/01 12:00 13:00 P01 E1
2. - - -
3. - - -
4. - - -
5. - - -
6. - - -
7. - - -
8. - - -
The error programme will be
displayed in grey with an asterisk
and have an error number.
The error programme will be deleted once you check the error in the programme list, or once you cancel
the timer-standby mode and re-enter it.
Press [CLEAR] to erase the selected programme.
32 EN
Recording
Timer Recording (cont'd)
3
Check the information on the
list you will need.
4
To clear the timer program-
ming, select the desired pro-
VPS
PDC
gramme using [Cursor K / L],
ON
then press [CLEAR].
To correct the timer program-
ON
ming
ON
1) Select the desired programme
using [Cursor K / L], then
press [ENTER].
2) Correct the timer programming
using [Cursor K / L / { / B].
3) Press [ENTER] again.
5
Press [TIMER PROG. SHOWVIEW]
to exit.
6
Press [ OPERATE] to return to
the timer-standby mode.
VPS
To check the timer program-
PDC
ON
ming in process
Press [TIMER PROG. SHOWVIEW].
The error numbers indicate:
E1-22 Recording error
E37-39
E23-24 Unrecordable disc
VPS
PDC
ON E25 • Copy prohibited programme
• Cannot record because of the
NTSC / PAL-60 signal is received.
E26-28 Copy prohibited programme
E29 Disc protected
E30 Disc full
E31 Already recorded 99 titles (Video
mode)
E32 Already recorded 99 titles (VR
mode)
OPERATE
TIMER PROG.
1
ZOOM
SHOW VIEW
.@/: ABC DEF
6
1 2 3
GHI JKL MNO
4 5 6
PQRS TUV WXYZ
7 8 9
DISPLAY SPACE CLEAR
0
TOP MENU MENU/LIST RETURN
K
{
L
REC MODE REV PLAY
B
h
RAPID PLAY SKIP PAUSE
H F
REC/OTR STOP
C
DVD RECORDER
NB033
Note
• If a timer recording is
proceeding, that programme
is highlighted in red. In such
a case, you cannot select any
other programmes.
Note
• [STOP C] on the remote
control is not effective.
E33 Already recorded 999 chapters
E34 No space for Control information
E35 PCA (Power Calibration Area) full
E36 Already finalised Video format disc
E40 • There are some unrecorded
parts due the overlapped timer
programmes.
• Recording did not start at the
start time.
E41 Power failure
E42 No disc
OPEN/CLOSE
2
A
5
PROG.
AUDIO 6
SETUP
ENTER
4
B
FWD
g
SKIP
G
CM SKIP