Table of Contents
Advertisement
Checking, cancelling, or correcting the timer
programming information
In the following example, No.
5 timer programming overlaps
on No. 1 and No. 6 timer
programmes. In such a case, you
should correct the programme
time to clear the overlap.
Timer Programming
Date
Start
End
1. 01/01
12:00
13:00
2. - - -
3. - - -
No.1 6
4. - - -
5. 01/01
12:30
14:00
6. 01/01
13:45
21:00
7. - - -
8. - - -
1
Press [T-SET] so that the
icon disappears from the front
panel display.
2
Press [TIMER PROG.].
Timer Programming list will
appear.
Timer Programming
Date
Start
End
1. 01/01
12:00
13:00
2. - - -
3. - - -
4. - - -
5. - - -
6. - - -
7. - - -
8. - - -
To stop the timer recording in progress
Press [STOP C] to stop the disc recording or [STOP C/EJECT A] to
stop the tape recording on the front panel of the unit.
If the timer programming did not complete correctly
The error number appears on the
Timer Programming list.
Timer Programming
Date
Start
End
01/01
12:00
13:00
*
2. - - -
3. - - -
The error programme will be
displayed in grey with an asterisk
and have an error number.
The error programme will be
deleted once you check the error
in the programme list, or once
you cancel the timer-standby
mode and re-enter it.
Press [CLEAR/C-RESET] to erase
the selected programme.
Downloaded from:
http://www.usersmanualguide.com/
Timer Recording (cont'd)
3
Check the information on the
list you will need.
4
To clear the timer program-
VCR
DVD
ming, select the desired pro-
DVD
CH
Mode
VCR
gramme using [Cursor K / L],
P01
DVD
XP
then press [CLEAR/C-RESET].
Overlap
To correct the timer program-
P02
DVD
SP
ming
P12
DVD
SEP
1) Select the desired programme
using [Cursor K / L], then
press [ENTER].
2) Correct the timer programming
using [Cursor K / L / { / B].
3) Press [ENTER] again.
5
Press [TIMER PROG.] to exit.
6
Press [T-SET] to return to the
timer-standby mode.
VCR
DVD
To check the timer program-
DVD
CH
Mode
ming in process
VCR
P01
DVD
XP
Press [TIMER PROG.].
The error numbers indicate:
E1-22
VCR
DVD
E37-39
DVD
CH
Mode
VCR
P01
DVD
E1
E23-24
E25
E26-28
E29
E30
E31
E32
E33
Recording
Recording error
Unrecordable disc
• Copy prohibited programme
• Cannot record because of the
NTSC / PAL-60 signal is received.
Copy prohibited programme
Disc protected
Disc full
Already recorded 99 titles (Video
mode)
Already recorded 99 titles (VR
mode)
Already recorded 999 chapters
OPERATE
OPEN/CLOSE
SETUP
DUBBING
EJECT
1
T-SET
TIMER PROG.
REC MODE
RAPID PLAY
VCR
DVD
CM SKIP
ZOOM
6
TOP MENU
MENU LIST
ENTER
RETURN
.@/:
ABC
DEF
1
2
3
GHI
JKL
MNO
6
4
5
PQRS
TUV
WXYZ
7
8
9
CLEAR/C-RESET
SPACE
DISPLAY
0
REV
FWD
PLAY
VCR
REC/OTR
REC/OTR
STOP
Note
• If a timer recording is
proceeding, that programme
is highlighted in red. In such
a case, you cannot select any
other programmes.
• When you check the timer
programming in progress
by pressing [TIMER PROG.]
during operations of the
component (VCR or DVD)
which is not currently used
for the timer recording,
the programme will not be
highlighted. In this case,
you cannot select other
programmings.
Note
• [STOP C] on the remote
control is not effective.
E34
No space for Control information
E35
PCA (Power Calibration Area) full
E36
Already finalised Video format disc
E40
• There are some unrecorded
parts due the overlapped timer
programmes.
• Recording did not start at the
start time.
• There is no tape in the cassette
compartment.
• Tape recording reaches to
the tape end during timer
recording.
E41
Power failure
E42
No disc
2
5
6
PROG.
SKIP
4
DVD
EN
33
Advertisement
Table of Contents
