Haier HWM60-78 User Manual page 6

Adjust the Installation position
The washing machine away from wall should be overrun 20mm. The largest allowable slope of the shank base
of the machine is 1 .The slanting or rough ground will result inunstable running or stoppage of the machine.
Please adjust it with following methods:
Confirm it's horizontal:
Hang the lead line to check if it is
horizontal.
Adjust the adjustable leg:
1 .To twist the adjustable leg, please first lift up the
side of the leg slightly, loosen the adjustable nut,
and twist the leg.
2 . After adjustment, fasten the nut.
Usage the drain hose
The drainage shall be smooth with the drain hose.
The height of the drain hose shall be less than 10cm,
or the drainage will not be smooth, and cost such long
time that the machine may stop at mid way.
Do not step on or press the drain hose.
If the drain hose is too long, cut it at mid point. To make
smooth drainage, cut the front end of the hose slantingly.
Before Using Before Using
the adjustable nut
Fasten
Loosen
the adjustable feet
High
Low
If extra drain hose is needed, please make separate
purchase. The inner diameter of the extra hose shall
not less than 30mm, and the length shall not exceed
1.5m.
> 30mm
<10cm
<1.5m
If the extra hose is too long,cut it either at
A or at B point.
B
A A
After switching on the power, the washing machine will set to common program including"wash, rinse,
spin "automatically. To select other procedures, push the "soak", " wash", " rinse" or "spin" button
to select the time of soak, wash and spin, and the times of rinse. After switching on the power, if you
push one of the button among "wash", "rinse"and"spin", the digitron of the former procedures will
turn off automatically. The former procedures will not run. For instance: after switching on the power. If
you push the "spin" button first, it will execute spin singly after starting.
Attention
.
Even there's no water in the tub, a certain period is
required before spin starting.
Do not use the soak program for the woolen textiles.
Separate the laundries that are not colorfast from
other laundries in washing.
The pulsator will not rotate unless the water is
filled to selected water level.
The soak procedure can work in cooperation with automatic programs like standard, jeans, chemical fiber and
cotton.There is intermittent pulsator stirring during soak.
After the machine starts operation, you can only set the program and procedure during washing, and can not
make setting in other cases.
Press " WATER LEVEL "button,
select suitable water level
After switching on the power, the washing machine will execute fuzzy program automatically to detect the cloth.
After defection, it can set the water level automatically. To select other water level, first push the "start/pause"
button, then push the "water level" button to set the water level. Refer to "standard dosage of detergent and
water quantity"in Page 9 and "water level button"in Page 11 for selection.
Page 9
Water Level and Time Table for Each Program (self programming not included)
Program Water level Wash (min) Rinse (min/time)
Normal 1-10 About 9-12 Rinse twice, about 2
each time
Quick 1-10 About 5 Save water program, total 8 around
Posthaste 3 About 2 Save water program, total 4 around
Jean 1-10 About 20 Rinse twice, about 5
each time
Normal 1-10 About 10-16 Save water program total 10 around
Cotton 1-10 About 10 Rinse twice, about 3
Woollen 1-10 About 3 Rinse twice, about 2
Silk 1-10 About 5 Rinse twice, about 2
Using process Using process
WATER
LEVEL
Page 11
Spin (min) Total time
(min)
About 34-37
About 15
About 6
About 7 About 54
About 19-25
About 5 About 48
About 3 About 25
About 4 About 30