Directed CHRYSLER9 Manual
  1. Manuals
  2. Brands
  3. Directed Manuals
  4. Automobile Accessories
  5. CHRYSLER9
  6. Manual

Directed CHRYSLER9 Manual

Hide thumbs Also See for CHRYSLER9:
Table of Contents

Advertisement

Quick Links

Download this manual
Directed Digital System
CHRYSLER9
Firmware Specific Guide
This product is intended for installation by a professional
installer only! Attempts to install this product by a person
other than a trained professional may result in severe
damage to a vehicle's electrical system and components.
© 2015 Directed, Vista, CA
Directed Digital System 2015-04

Advertisement

Table of Contents
loading

Related Manuals for Directed CHRYSLER9

Summary of Contents for Directed CHRYSLER9

  • Page 1 This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional may result in severe damage to a vehicle’s electrical system and components. © 2015 Directed, Vista, CA Directed Digital System 2015-04...

  • Page 2: Table Of Contents

    Contents Warning! Safety first ........................3 Introduction ............................ 4 Vehicle application guide ......................4 Wiring connections ......................... 5 Main power harness (H1), 12-pin thick gauge connector ............... 5 Auxiliary output harness (H2), 16-pin black connector ..............5 Analog harness (H3), 18-pin white connector ................6 MC501 harness (H4), 8 thick-gauge wires (optional) ..............

  • Page 3: Warning! Safety First

    This testing should be performed by an authorized Directed dealer in accordance with the Safety Check outlined in this product installation guide. If the vehicle starts in gear, cease remote start operation immediately and consult with the user to fix the problem immediately.

  • Page 4: Introduction

    Introduction The CHRYSLER9 firmware for Directed Digital Systems is a complete solution for remote start, security (if applicable), bypass interface, and convenience needs compatible with specific Jeep vehicles. Warning! This module can only be programmed via the web tool, which can be found on www.directechs.com or using the Directechs Mobile application for smartphones.

  • Page 5: Wiring Connections

    If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relay may be necessary. Directed Digital System CHRYSLER9 © 2015 Directed. All rights reserved.

  • Page 6: Analog Harness (H3), 18-Pin White Connector

    These connections are only required if the corresponding statuses are not supported by the firmware. See "Vehicle application guide" on page 4 for a list of compatible features. Directed Digital System CHRYSLER9 © 2015 Directed. All rights reserved.

  • Page 7: Installation

    Required for RAP, heated seats, steering wheel and rear defroster control. Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic connector. Directed Digital System CHRYSLER9 © 2015 Directed. All rights reserved.

  • Page 8: Wiring Diagram (With T-Harness)

    This connection is only required when the EIPS (Engine Idle Protection System) feature is activated. With the exception of the OBDII diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise). Directed Digital System CHRYSLER9 © 2015 Directed. All rights reserved.

  • Page 9: Vehicle Wiring Reference Charts

    Manual or automatic transmission selection The yellow loop on the Directed Digital System controls which transmission type the unit is configured for. The state of the loop (uncut or cut) when the main module is powered up will determine which type is selected.

  • Page 10: Optional Sensors

    When flashing the Directed Digital System, make sure to pick the remote you will be using. This way the main module will have the necessary firmware to interact with the remote and Control Center (antenna) combination.

  • Page 11: Module Programming

    Connect all but the white 12-pin harness Connect all the harnesses to the Directed Digital System, EXCEPT the white12-pin main power harness. Must be connected LAST Connect the white12-pin main power harness, and wait until the LED turns &...

  • Page 12: Led Diagnostics And Troubleshooting

    Turn the ignition off then back on value. If a second or more attempt to try again. fails, connect the module to Flashes red x4 Directechs and call Tech Support with the module ID in hand. Directed Digital System CHRYSLER9 © 2015 Directed. All rights reserved.
  • Page 13 If the bypass module fails to flash, it means Commands can come from RF or UNLOCK command received. the module did not receive the signal. D2D. Flashes orange TRUNK command received. Flashes orange Directed Digital System CHRYSLER9 © 2015 Directed. All rights reserved.

  • Page 14: Module Reset

    After 3 seconds the LED turns ON solid orange. Keep holding the & & programming button until the LED flashes red, then orange slowly. Solid Hold Flashes Release the programming button. The LED turns ON solid red. & Solid Release Directed Digital System CHRYSLER9 © 2015 Directed. All rights reserved.

  • Page 15: Learning The Tach (Not Needed With Virtual Tach)

    Important! After successfully learning Virtual Tach, a small minority of vehicle starters may over crank or under crank during remote start. Use the VirtualTach Fine tune feature in the configuration wizard to adjust the starter output time in 50mS increments to compensate for such an occurrence. Directed Digital System CHRYSLER9 © 2015 Directed. All rights reserved.

  • Page 16: Limited Lifetime Consumer Warranty

    Directed dealer; the unit will be professionally reinstalled in the vehicle in which it was originally installed by an authorized Directed dealer; and the unit is returned to Directed, shipping prepaid with a legible copy of the bill of sale or other dated proof of purchase bearing the following information: consumer’s name, telephone number and address;...

  • Page 17: Quick Reference Guide - Viper, Clifford, Python, Avital & Automate

    * This output is configurable. see your authorized installation center for more information. This unique feature monitors a variety of parameters such as the key fob, vehicle speed sensor and door sensor, in order to perform takeover securely. Directed Digital System CHRYSLER9 © 2015 Directed. All rights reserved.
  • Page 18 SmartStart compatible Engine Idle Protection System (EIPS) This system is compatible with Directed SmartStart 3.0. For a complete list of Vehicles equipped with a push button start or push-to-start keyless ignition and start supported features, please visit www.mysmartstart.com. system work by using various antennas throughout the vehicle to detect the presence of the vehicle's electronic Smart Key.
  • Page 19 Notes Directed Digital System CHRYSLER9 © 2015 Directed. All rights reserved.

  • Page 20: Quick Reference Guide - Autostart

    * This output is configurable. see your authorized installation center for more information. This unique feature monitors a variety of parameters such as the key fob, vehicle speed sensor and door sensor, in order to perform takeover securely. Directed Digital System CHRYSLER9 © 2015 Directed. All rights reserved.
  • Page 21 SmartStart compatible Engine Idle Protection System (EIPS) This system is compatible with Directed SmartStart 3.0. For a complete list of Vehicles equipped with a push button start or push-to-start keyless ignition and start supported features, please visit www.mysmartstart.com. system work by using various antennas throughout the vehicle to detect the presence of the vehicle's electronic Smart Key.
  • Page 22 Notes Directed Digital System CHRYSLER9 © 2015 Directed. All rights reserved.

Table of Contents