Table of Contents
Advertisement
Quick Links
INSTALLATION GUIDE
CHRYSLER9
Designed by Installers for Installers
© 2020 Directed, Vista CA
This product is intended for installation by a professional installer only! Attempts to install this
product by a person other than a trained professional may result in severe damage to a vehicle's
electrical system and components.
2020-01-16
Directed Digital
Solutions
Advertisement
Table of Contents
Related Manuals for Directed Directechs CHRYSLER9
Summary of Contents for Directed Directechs CHRYSLER9
- Page 1 CHRYSLER9 Designed by Installers for Installers © 2020 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional may result in severe damage to a vehicle’s electrical system and components.
-
Page 2: Table Of Contents
Contents Warning! Safety first ........................3 Introduction ............................ 4 Pre-installation and application warnings ..................4 Vehicle application guide ......................5 Wiring connections ......................... 6 Main power harness (H1), 12-pin thick gauge connector ............... 6 Auxiliary output harness (H2), 16-pin black connector ..............6 Analog harness (H3), 18-pin white connector ................ -
Page 3: Warning! Safety First
The following safety warnings must be observed at all times: • Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer. • When properly installed, this system can start the vehicle via a command signal from the remote control. Therefore, never operate the system in an area that does not have adequate ventilation. -
Page 4: Introduction
Introduction The CHRYSLER9 firmware for Directed Digital Solutions is compatible with specific Jeep vehicles. It is a complete solution for remote start, security (if applicable), bypass interface, and convenience. This guide provides information on the installation of the module using CHRYSLER9. If you would prefer using this system as a digital solution, go to www.directechs.com and search for the make, model and year of the vehicle. -
Page 5: Vehicle Application Guide
DL: OE Door Lock & Alarm Controls KI: Ignition Key Switch Interface PK: Transponder & Immobilizer Override RS: Remote Start & Engine Controls SS: Integrated Security & Monitoring ST: Function/Feature Status Directed Digital Solutions CHRYSLER9 © 2020-01-16 Directed. All rights reserved. -
Page 6: Wiring Connections
If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relay may be necessary. Directed Digital Solutions CHRYSLER9 © 2020-01-16 Directed. All rights reserved. -
Page 7: Analog Harness (H3), 18-Pin White Connector
These connections are only required if the corresponding statuses are not supported by the firmware. See "Vehicle wiring reference chart" on page 10 for a list of compatible features. Directed Digital Solutions CHRYSLER9 © 2020-01-16 Directed. All rights reserved. -
Page 8: Installation (Wiring Diagrams & Vehicle Wiring Reference Charts)
(-) Hood Input: Gray: 3 (-) Rear Left Door Trigger: Violet/Gray, pin 36 (-) RAP Shutdown Output: Brown/Black: 8 12-pin (+) Siren Output: Brown: 17 White Connector Siren Directed Digital Solutions CHRYSLER9 © 2020-01-16 Directed. All rights reserved. - Page 9 Activation Input Siren (-) Rear Left Door Trigger: Violet/Gray, pin 36 Brake Switch (black connector) (green connector at BCM, under driver side dash) (+) Brake: Dk. Green/Lt. Green, pin 1 Directed Digital Solutions CHRYSLER9 © 2020-01-16 Directed. All rights reserved.
- Page 10 CAN C High Gray/White Data OBDII connector. Black CAN C Low Yellow Data OBDII connector. Black IHS CAN High Gray Data OBDII connector. Black IHS CAN Low White Data OBDII connector. Black Directed Digital Solutions CHRYSLER9 © 2020-01-16 Directed. All rights reserved.
-
Page 11: Connecting The Module
Manual or automatic transmission selection The yellow loop on the Directed Digital Solutions controls which transmission type the unit is configured for. The state of the loop (uncut or cut) when the main module is powered up will determine which type is selected. -
Page 12: Optional Sensors
When flashing the Directed Digital Solutions, make sure to pick the remote you will be using. This way the main module will have the necessary firmware to interact with the remote and Control Center (antenna) combination. -
Page 13: Module Programming
Connect all but the 12-pin harness Connect all the harnesses to the Directed Digital Solutions, EXCEPT the 12-pin main power harness. Must be connected LAST Connect the 12-pin main power harness, and wait until the LED turns ON solid red. -
Page 14: Led Diagnostics And Troubleshooting
External module synchronization Description Troubleshooting OBDII feature not supported. The diagnostic data bus was not detected, therefore the SmartStart features will be limited. (Flashes red, red, then orange) x 10 Directed Digital Solutions CHRYSLER9 © 2020-01-16 Directed. All rights reserved. - Page 15 The vehicle was detected as moving, which prevents the system from shutting it down. Flashes red x 4 Analog error codes Description Troubleshooting DEI feature error. A feature config file mismatch was detected. Please contact Technical Support. Flashes red, green & orange Directed Digital Solutions CHRYSLER9 © 2020-01-16 Directed. All rights reserved.
-
Page 16: Soft Reset
A module reset will only erase the steps performed in "Module programming" on page 13. The firmware and settings flashed to the module will not be affected. Connect all but the If required for your installation, connect all the harnesses to the Directed Digital Solutions, 12-pin harness EXCEPT the 12-pin main power harness. Press and hold the programming button, then connect the 12-pin harness to the module. -
Page 17: Learning The Tach (Not Needed With Virtual Tach)
Important! After successfully learning Virtual Tach, a small minority of vehicle starters may over crank or under crank during remote start. Use the VirtualTach Fine tune feature in the configuration wizard to adjust the starter output time in 50mS increments to compensate for such an occurrence. Directed Digital Solutions CHRYSLER9 © 2020-01-16 Directed. All rights reserved. -
Page 18: Limited Lifetime Consumer Warranty
Directed dealer, the unit was professionally installed and serviced by an authorized Directed dealer; the unit will be professionally reinstalled in the vehicle in which it was originally installed by an authorized Directed dealer; and the unit is returned to Directed, shipping prepaid with a legible copy of the bill of sale or other dated proof of purchase bearing the following information: consumer’s name, telephone number and address;... -
Page 19: Quick Reference Guide
Factory remote. Press the Remote Start button on the transmitter.* • Aftermarket remote. • Directed SmartStart application via your smartphone. & The parking lights will flash once to indicate the Parking lights flash x1 Press Remote vehicle is now in Pit Stop Mode. - Page 20 SmartStart compatible This system is compatible with Directed SmartStart. For a complete list of supported features, please visit www.mysmartstart.com. What is SmartStart? Now you can remote start, lock and unlock your car just by pushing a button on your smartphone; using the SmartStart App from Directed, the leader in vehicle security and remote start.