Kärcher WRP 1000 comfort Manual page 12

Fuses
1 F1 Fuse Controls
2 F2 Fuse Motor filament filter
3 F3 Fuse Motor multiport valve
Accessories
Filter inlay
Order No. 5.033-239.0
Attachment set 'Fresh water switching'
Order No. 2.641-521.0
Manual switching between processed/
fresh water for using fresh water in the
high-pressure cleaner (for e.g. for rinsing).
Attachment set input valve
Order No. 4.640-230.0
Upgrade kit - submersion pump
Order No. 6.474-073.0
Attachment kit ventilation
Order No. 2.641-510.0
Installing the unit (only for
experts)
Notice
The equipment may only be installed by an
mechanic of Kärcher
–
or an from Kärcher authorized individual
–
Preparing the installation place
The following requirements are necessary
in order to install the equipment:
frost-free room with adequate ventila-
–
tion and exhausts
Floor path for collecting sludge
–
Strong wall for fastening the system
–
For electrical connection refer to techni-
–
cal specifications.
Unpack the equipment
Unpack the equpiment and dispose of the
packing material properly.
12
Water installation
The water installation depends on the spe-
cific conditions of the existing plant compo-
nents such as
Type and model of high pressure cleaner
–
Note
The processed water outlet of the system is
directly connected to the water inlet of the
high-pressure cleaner. This can lead to
foam formation in the swimmer tank in
high-pressure cleaners with a swimmer
tank. In such a case, the high-pressure
cleaner must be switched to suction opera-
tioins (see separate operating instructions
of the high-pressure cleaner).
Type and models of building-side compo-
–
nents (sludge collector, pump basin, etc.)
Nominal widtht, lengths and type of
–
channels
Hence, the water installation must be done
according to the specific local conditions.
The immersion pump specifications in the
building must meet the requirements out-
line in the "Technical Data / Immersion
Pump Requirements" section.
Danger
Risk of injury on account of tripping and falling.
Lay the hoses of the plant in such a way
that they do not pose a risk for tripping and
falling.
Electrical connection
Warning
The appliance may only be connected
–
to alternating current.
The appliance may only be connected
–
to an electrical supply which has been
installed in accordance with IEC 60364.
The voltage indicated on the type plate
–
must correspond to the voltage of the
electrical source.
The appliance should always be con-
–
nected to the electrical mains using a
plug. It is forbidden to permanently con-
nect the appliance to the power supply.
The plug is only for mains separation.
For connection values, see type plate/tech-
nical data.
5
-
EN
CE declaration
We hereby declare that the machine de-
scribed below complies with the relevant
basic safety and health requirements of the
EU Directives, both in its basic design and
construction as well as in the version put
into circulation by us. This declaration shall
cease to be valid if the machine is modified
without our prior approval.
Product: Effluent treatment plant
Type: 1.217-xxx
Relevant EU Directives
2006/42/EC (+2009/127/EC)
2004/108/EC
Applied harmonized standards
EN 60204–1
EN 55014–1: 2006 + A1: 2009
EN 55014–2: 1997 + A2: 2008
EN 61000–3–2: 2006 + A2: 2009
EN 61000–3–3: 2008
EN 62233: 2008
The undersigned act on behalf and under
the power of attorney of the company man-
agement.
CEO Head of Approbation
Authorised Documentation Representative
S. Reiser
Alfred Kärcher GmbH Co. KG
Alfred-Kärcher-Str. 28 - 40
71364 Winnenden (Germany)
Phone: +49 7195 14-0
Fax: +49 7195 14-2212
Winnenden, 2010/11/01