DeWalt DCS777 Original Instructions Manual page 40

EnGLIsh
For example, the Transport Wh rating Example of Use and Transport Label Marking
might indicate 3 x 36 Wh, meaning 3
batteries of 36 Wh each. The Use Wh
rating might indicate 108 Wh
(1 battery implied).
Storage Recommendations
1. The best storage place is one that is cool and dry away from direct
sunlight and excess heat or cold. For optimum battery performance and
life, store battery packs at room temperature when not in use.
2. For long storage, it is recommended to store a fully charged battery
pack in a cool, dry place out of the charger for optimal results.
nOTE: Battery packs should not be stored completely depleted of charge.
The battery pack will need to be recharged before use.
Labels on Charger and Battery Pack
In addition to the pictographs used in this manual, the labels on the charger
and the battery pack may show the following pictographs:
Read instruction manual before use.
See Technical Data for charging time.
Do not probe with conductive objects.
Do not charge damaged battery packs.
Do not expose to water.
Have defective cords replaced immediately.
Charge only between 4 ˚C and 40 ˚C.
Only for indoor use.
Discard the battery pack with due care for the environment.
Charge D WALT battery packs only with designated D
e
chargers. Charging battery packs other than the designated
D WALT batteries with a D
e
or lead to other dangerous situations.
Do not incinerate the battery pack.
USE (without transport cap). Example: Wh rating indicates 108
Wh (1 battery with 108 Wh).
TRANSPORT (with built-in transport cap). Example: Wh rating
indicates 3 x 36 Wh (3 batteries of 36 Wh).
Battery Type
The DCS777 operates on a 54 volt battery pack.
These battery packs may be used: DCB546, DCB547, DCB548. Refer to
Technical Data for more information.
Package Contents
The package contains:
1 Partly assembled machine
2 Hex keys (4 mm and 6 mm)
1 216 mm TCT saw blade
38
WALT
e
WALT charger may make them burst
e
1 Material clamp
2 Battery packs (T2 model)
1 Charger (T2 model)
2 Base extention handles and installation hardware
1 Instruction manual
• Check for damage to the tool, parts or accessories which may have
occurred during transport.
• Take the time to thoroughly read and understand this manual prior
to operation.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
Wear ear protection.
Wear eye protection.
Keep hands away from blade.
Keep hands 100 mm from either side of saw blade.
Do not stare directly into the light source.
Carrying point.
Date Code Position (Fig. B)
The Date Code 32 , which also includes the year of manufacture, is printed
into the housing.
2019 XX XX
Year of Manufacture
Description (Fig. A–D)

WARNING: Never modify the power tool or any part of it. Damage or
personal injury could result.
On/off switch
1
2 Guard lock up release lever
Fixed upper guard
3
Outer flange
4
Blade bolt
5
6 Lower blade guard
Saw blade
7
Sliding fence lock knob
8
Fixed table
9
10 Kerf plate
Mitre arm
11
Mitre latch
12
Rotating table/mitre arm
13
Mitre scale
14
15 Sliding fence
Material clamp
16
Intended Use
Your D WALT cordless compact mitre saw has been designed for
e
professional cutting wood, wood products and plastics. When using the
appropriate saw blades, sawing aluminum is also possible. It performs the
Rail lock knob
17
18 Bevel clamp handle
Bevel scale
19
Bench mounting holes
20
Lock down pin
21
22 Rails
Saw head
23
Hex wrenches (Fig. D)
24
Battery pack
25
26 Battery pack release button
Fuel gauge button
27
Lock off switch
28
Bevel override button
29
Dust extraction port
30
31 Base extention handles
Date code
32