English MITRE SAW DCS727-XE Congratulations! An estimation of the level of exposure to vibration and/or noise should also take into account the times when the tool is switched off or when You have chosen a D WALT tool. Years of experience, thorough product it is running but not actually doing the job.
English b ) Use clamps to support the workpiece whenever possible. If o ) Always use a clamp or a fixture designed to properly support supporting the workpiece by hand, you must always keep your round material such as rods or tubing. Rods have a tendency to hand at least 100 mm from either side of the saw blade.
English USE ONLY CROSSCUT SAW BLADES recommended for mitre saws. • • crystalline silica from bricks and cement and other masonry For best results, do not use carbide tipped blades with hook angles in products, and excess of 7 degrees. Do not use blades with deep gullets. These can deflect •...
English Charging a Battery (Fig. B) When using a cable reel, always unwind the cable completely. Important Safety Instructions for All Battery Chargers 1. Plug the charger into an appropriate outlet before inserting battery pack. SAVE THESE INSTRUCTIONS: This manual contains important safety 2.
English Charger Cleaning Instructions WALT batteries comply with all applicable shipping regulations as prescribed by industry and legal standards which include UN WARNING: Shock hazard. Disconnect the charger from the AC Recommendations on the Transport of Dangerous Goods; International Air outlet before cleaning.
Intended Use Your D WALT DCS727-XE mitre saw has been designed for professional cutting of wood, wood products and plastics. When using the appropriate saw blades, sawing aluminium is also possible. It performs the sawing operations of cross-cutting, bevelling and mitring easily, accurately...
English DO nOT use under wet conditions or in the presence of flammable liquids Always mount your saw firmly to a stable surface to prevent movement. or gases. To enhance the tool’s portability, it can be mounted to a piece of 12.7 mm or thicker plywood which can then be clamped to your work support or This mitre saw is a professional power tool.
English 5. Install the blade screw and, engaging the spindle lock, tighten the To reverse the crown bevel pawl, remove the retaining screw, the 22.5° bevel pawl 56 and the 30° crown bevel pawl 57 . Flip the crown bevel screw firmly with wrench provided (turn counterclockwise, left- pawl ...
English Guard Actuation and Visibility (Fig. Y) 2. With the mitre lock handle unlocked, allow the mitre latch to snap into place as you rotate the mitre arm to zero. The lower guard 1 on your saw has been designed to automatically 3.
Page 20
English Proper Body and Hand Position (Fig. O1, O2) External Dust Extraction (Fig. AA) When vacuuming dry dust that is especially detrimental to health or WARNING: To reduce the risk of serious personal injury, ALWAYS use carcinogenic, use a special dust Class M vacuum cleaner. proper hand position as shown in Figure O1.
Page 21
English are shorter in length, always place the longer side against the fence. Use the material clamp provided with your saw. The left or right fence 39 will slide from side to side to aid in clamping. Other aids such as spring Bevel Cut (Fig.
Page 22
English For a shape that is not shown in the chart, use the following formula: 180° Right side Mitre right 45° Mitre left 45° divided by the number of sides equals the mitre (if the material is cut Save right side of cut Save right side of cut vertically) or bevel angle (if the material is cut laying flat).
English Aluminum Cutting (Fig. W1, W2) Periodically clean all dust and wood chips from around AND UNDER the base and the rotary table. ALWAYS USE THE APPROPRIATE SAW BLADE MADE ESPECIALLY FOR CUTTING ALUMINUM. Worklight Cleaning Certain workpieces may require the use of a clamp or fixture to prevent •...
Page 24
Belgique et WALT - Belgium BVBA Tel: NL 32 15 47 37 63 www.dewalt.be luxembourg België en luxemburg Egide Walschaertsstraat 16 Tel: FR 32 15 47 37 64 enduser.BE@sBDinc.com 2800 Mechelen Fax: 32 15 47 37 99 Danmark WALT (Stanley Black&Decker AS)